Home » Seagate Manuals » Hard Drives » Seagate STM303004N1AAAS-RK » Manual Viewer

Seagate STM303004N1AAAS-RK DiamondMax 21 SATA Product Manual - Page 39

Serial ATA SATA interface

UPC - 751921029914

View all Seagate STM303004N1AAAS-RK manuals

Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0-4; multiword DMA modes 0-2, and Ultra DMA modes 0-6. For detailed information about the Serial ATA interface, refer to the "Serial ATA: High Speed Serialized AT Attachment" specification. 4.1 Hot-Plug compatibility DiamondMax 21 drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA Revision 2.5 specification. This specification can be downloaded from www.serialata.org. DiamondMax 21 Serial ATA Product Manual, Rev. C 33

Section	Page
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Specification summary tables	9
2.2 Formatted capacity	22
2.2.1 LBA mode	22
2.3 Default logical geometry	22
2.4 Recording and interface technology	23
2.5 Physical characteristics	24
2.6 Seek time	25
2.7 Start/stop times	25
2.8 Power specifications	25
2.8.1 Power consumption	26
2.8.1.1 Typical current profiles	27
2.8.2 Conducted noise	27
2.8.3 Voltage tolerance	27
2.8.4 Power-management modes	28
2.9 Environmental specifications	29
2.9.1 Ambient temperature	29
2.9.2 Temperature gradient	29
2.9.3 Humidity	29
2.9.3.1 Relative humidity	29
2.9.3.2 Wet bulb temperature	29
2.9.4 Altitude	29
2.9.5 Shock	29
2.9.5.1 Operating shock	29
2.9.5.2 Nonoperating shock	30
2.9.6 Vibration	30
2.9.6.1 Operating vibration	30
2.9.6.2 Nonoperating vibration	30
2.10 Acoustics	31
2.11 Electromagnetic immunity	31
2.12 Reliability	32
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	32
2.13 Agency certification	32
2.13.1 Safety certification	32
2.13.2 Electromagnetic compatibility	32
2.13.3 FCC verification	33
2.14 Environmental protection	34
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive	34
2.14.2 China Restriction of Hazardous Substances (RoHS) Directive	34
2.15 Corrosive environment	34
3.0 Configuring and mounting the drive	35
3.1 Handling and static-discharge precautions	35
3.2 Configuring the drive	36
3.3 Serial ATA cables and connectors	36
3.4 Drive mounting	37
4.0 Serial ATA (SATA) interface	39
4.1 Hot-Plug compatibility	39
4.2 Serial ATA device plug connector pin definitions	40
4.3 Supported ATA commands	41
4.3.1 Identify Device command	43
4.3.2 Set Features command	47
4.3.3 S.M.A.R.T. commands	48
5.0 Maxtor support services	49
Index	51
A	51
B	51
C	51
D	51
E	51
F	51
G	51
H	51
I	52
K	52
L	52
M	52
N	52
O	52
P	52
Q	52
R	52
S	53
T	53
U	53
V	53

Match case Limit results 1 per page

DiamondMax 21 Serial ATA Product Manual, Rev. C

4.0

Serial ATA (SATA) interface

These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA

programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.

For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT

Attachment” specification.

4.1

Hot-Plug compatibility

DiamondMax 21 drives incorporate connectors which enable you to hot plug these drives in accordance with

the Serial ATA Revision 2.5 specification. This specification can be downloaded from www.serialata.org.