Sharp AR-207 AR-207 Operation Manual - Page 55

mode, press the light

Get Sharp AR-207 PDF manuals and user guides View all Sharp AR-207 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

USER PROGRAMS 4 Select the desired parameter using the numeric keys. q The entered parameter number will blink on the right side of the copy quantity display. q The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min., press key 2. Program name Parameters Auto clear time 0 OFF 1 30 sec. * 2 60 sec. 3 90 sec. 4 120 sec. 5 10 sec. Preheat mode 0 OFF 1 30 sec. 2 60 sec. * 3 90 sec. 4 120 sec. Auto power shut-off timer * 1 30 min. 2 60 min. 3 90 min. 4 120 min. 5 240 min. Stream feeding mode * 0 OFF 1 ON Auto power shut-off setting 0 OFF * 1 ON Border line for 2 in 1 or 4 in 1 * 0 OFF 1 ON Rotation copy 0 OFF * 1 ON Auto paper select mode 0 OFF * 1 ON Auto tray switching 0 OFF * 1 ON Erase width adjustment 0 0" 1 1/4" * 2 1/2" 3 3/4" 4 1" Layout in 2 in 1 copy * 1 Pattern 1 2 Pattern 2 Layout in 4 in 1 copy * 1 Pattern 1 2 Pattern 2 3 Pattern 3 4 Pattern 4 Offset of paper output tray 0 Upper OFF, lower OFF 2 Upper ON, lower OFF * 1 Upper ON, lower ON 3 Upper OFF, lower ON Image rotation in duplex copying * 0 OFF 1 ON Location of the margin * 1 Left 2 Top Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 37. If you select "0" (OFF) in a program, the corresponding function will be disabled. 5 Press the START key. q The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. GENERAL INFORMATION User programs 6 To continue with other user programs, press the key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key. q All the alarm indicators will go out. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
53
GENERAL INFORMATION
USER PROGRAMS
4
Select the desired parameter using the numeric keys.
●
The entered parameter number will blink on the right side of the copy
quantity display.
●
The parameters are shown in the table below.
For example, to change the setting of the auto power shut-off timer to
60 min., press key 2.
5
Press the START key.
●
The right-hand number in the copy quantity display will be steadily lit
and the entered value will be stored.
6
To continue with other user programs, press the
key
and then repeat steps 2 to 5. To exit the user program
mode, press the light (
) key.
●
All the alarm indicators will go out.
User programs
Program name
Parameters
Auto clear time
0
OFF
1
30 sec.
* 2
60 sec.
3
90 sec.
4
120 sec.
5
10 sec.
Preheat mode
0
OFF
1
30 sec.
2
60 sec.
* 3
90 sec.
4
120 sec.
Auto power shut-off timer
* 1
30 min.
2
60 min.
3
90 min.
4
120 min.
5
240 min.
Stream feeding mode
* 0
OFF
1
ON
Auto power shut-off setting
0
OFF
* 1
ON
Border line for 2 in 1 or 4 in 1
* 0
OFF
1
ON
Rotation copy
0
OFF
* 1
ON
Auto paper select mode
0
OFF
* 1
ON
Auto tray switching
0
OFF
* 1
ON
Erase width adjustment
0
0"
1
1/4"
* 2
1/2"
3
3/4"
4
1"
Layout in 2 in 1 copy
* 1
Pattern 1
2
Pattern 2
Layout in 4 in 1 copy
* 1
Pattern 1
2
Pattern 2
3
Pattern 3
4
Pattern 4
Offset of paper output tray
0
Upper OFF, lower OFF
* 1
Upper ON, lower ON
2
Upper ON, lower OFF
3
Upper OFF, lower ON
Image rotation in duplex
* 0
OFF
1
ON
copying
Location of the margin
* 1
Left
2
Top
Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 37.
If you select “0” (OFF) in a program, the corresponding
function will be disabled.