Sharp AR-207 AR-207 Operation Manual - Page 61

Setting the power save modes, Copying from the preheat mode, Copying from the auto power shut-off

Get Sharp AR-207 PDF manuals and user guides View all Sharp AR-207 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

POWER SAVE MODES Setting the power save modes The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 52. q The copier will enter the preheat mode first and then the auto power shut- off mode after a preset time has elapsed when no copier operation has been made. q If conflicting settings are made with user programs No. 3 and No.5, the last program set will have priority. Copying from the preheat mode Make desired copier selections and press the START key using the normal copying procedure. q When any key input is made or any other copier operation is made, the POWER SAVE indicator will start to blink. q When the START key is pressed, the START key indicator will go out and copying will start within 10 seconds. The POWER SAVE indicator will go out when copying starts. Copying from the auto power shut-off mode q Only available when an optional printer expansion kit or facsimile expansion kit is installed. 1 Press the START key. q The copier will exit the auto power shut-off mode and the POWER SAVE indicator will start to blink. 2 Make desired copier selections and press the START key using the normal copying procedure. q It will take approximately 35 seconds for the copier to start copying. However, you can make desired settings and press the START key during warm-up. Copying will start after warm-up is finished. 59 GENERAL INFORMATION Power save modes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
59
GENERAL INFORMATION
Setting the power save modes
The time that elapses before the copier enters a power save mode after any
operation is made can be set manually. This time is set with user program No.
2 for the preheat mode and user program No. 3 for the auto power shut-off
mode. For these settings, see page 52.
●
The copier will enter the preheat mode first and then the auto power shut-
off mode after a preset time has elapsed when no copier operation has been
made.
●
If conflicting settings are made with user programs No. 3 and No.5, the last
program set will have priority.
Copying from the preheat mode
Make desired copier selections and press the START
key using the normal copying procedure.
●
When any key input is made or any other copier operation is made, the
POWER SAVE indicator will start to blink.
●
When the START key is pressed, the START key indicator will go out
and copying will start within 10 seconds. The POWER SAVE indicator
will go out when copying starts.
Copying from the auto power shut-off mode
●
Only available when an optional printer expansion kit or facsimile
expansion kit is installed.
1
Press the START key.
●
The copier will exit the auto power shut-off mode and the POWER
SAVE indicator will start to blink.
2
Make desired copier selections and press the START
key using the normal copying procedure.
●
It will take approximately 35 seconds for the copier to start copying.
However, you can make desired settings and press the START key
during warm-up. Copying will start after warm-up is finished.
Power save modes
POWER SAVE MODES