Sharp CD-BA200 CD-BA200 Operation Manual
Sharp CD-BA200 Manual
 |
View all Sharp CD-BA200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp CD-BA200 manual content summary:
- Sharp CD-BA200 | CD-BA200 Operation Manual - Page 1
MINI COMPONENT SYSTEM OPERATION MANUAL MODEL CD-BA200 Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. CD-BA200 Mini Component System consisting of CD-BA200 (main - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 2
THE CLOCK 6 SOUND CONTROL 7 COMPACT DISC OPERATION 8-10 RADIO OPERATION 11-12 CASSETTE OPERATION 12 12 Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 3
electronic/electrical equipment (home computers service to your local SHARP service disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player. q Do not write on either side of the disc protect CD pickup, tape heads, etc.) or on the transmitter LED on the remote - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 4
AC outlet before connecting or disconnecting any component. s Speaker connection Connect each speaker Model CP-BA200 is the exclusive speaker for the CD-BA200. Do not use it for other models. Besides, do not connect other speakers to the CD-BA200 - 200 Hz) Bi-amp system: q This product drives the - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 5
the internal digital electronics. Place the antenna away from the unit for better reception. q If the AM loop antenna and the FM antenna wire are placed near the AC power cord, interference may result. q Do not connect the attached FM antenna to an outdoor FM antenna. Otherwise, trouble may occur - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 6
mode. To cancel the demonstration mode: When the unit is in the stand-by mode (demonstration mode), press the X-BASS/DEMO button. q The demonstration mode indicated in the battery compartment. q Replace all old batteries with new ones at the transmitter LED on the remote control and the sensor on - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 7
) 2 3 4 AM 12:00 AM 0:00 0:00 5 6 7 8 9 In this example, the clock is set for the 12-hour (AM 12:00) system. 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Press the CLOCK button. 3 Within 5 seconds, press the MEMORY/SET button. 4 X W Press the TUNING/TIME ( or ) button to select - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 8
the VOLUME button to decrease the volume. 0 1 2 ..... 29 30 MAXIMUM (Main unit) (Remote control) X-BASS indicator s Extra bass (X-BASS) When the power is first turned on, the unit will enter the extra bass mode which emphasizes the bass frequencies, and "XBASS" will appear. To cancel the extra - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 9
playback: x 6 Press the CD button on the remote control. 6 q " " will appear. y 0R Press the button to resume playback from the same point. To stop playback: Press the s (CD s) button. To remove the CDs: While in the stop mode, press the OPEN/CLOSE button. q The disc tray will open. Remove the - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 10
stop CD operation. q If the beginning of the disc is reached while reviewing, the mode will automatically switch to normal playback at that point. s Random play (Remote control operation) The tracks on the disc(s) can be played in random order automatically. 1 Load a disc(s) and close the disc tray - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 11
be cleared, beginning with the last track programmed. Notes: q Opening the disc tray automatically cancels the programmed sequence. q Even if you press the ON/STAND-BY button to enter the stand-by mode or the function is changed from CD to some other function, the programmed selections will not be - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 12
button to tune into the desired station. X W Manual tuning: Press the TUNING/TIME ( or ) button Notes: q When radio interference occurs during or ) button again. 5 To receive an FM stereo transmission, press the TUNER (BAND) button so that button to enter the stand-by mode. Note: q The last station - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 13
the unit will enter the preset memory scan mode. Backup function: The backup function protects all station presets for a few hours should 6 Press the 0/R button to start playback. q When playback is performed using the remote control, press the TAPE 1 or TAPE 2 0 button. To stop playback: Press - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 14
STAND-BY CD TAPE (1 2) TUNER (BAND) TAPE 1 TAPE 2 CD ON/ STAND-BY CD TAPE TAPE 2 TAPE(1 2) TUNER (BAND) s Recording from the built-in radio 1 Tune in CD player (CD Synchronized Recording System) 1 Press the ON/STAND-BY button to turn the power on. 2 Press the CD button and load the desired disc. - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 15
Page 6) (Main unit operation) POWER Timer set indicator ON/ STAND-BY TIMER/ SLEEP CD TAPE (1 2) TUNER (BAND) TUNING/ TIME ( ) MEMORY/ SET 3 4 5 retained until a new time is entered. s Sleep operation The radio, compact disc and cassette deck can all be turned off automatically. 1 Play mode. 14 - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 16
using video equipment (Laser Disc player or VCR), be from the built-in radio" section on page 13 disc tray. q Remove all CDs inserted in the unit. 4 Press the OPEN/CLOSE button to close the disc tray. q Make sure that "NO DISC" is displayed. 5 Press the ON/STAND-BY button to enter the stand-by mode - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 17
, causing poor sound. Demagnetize these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetizer. Read the demagnetizer's instructions carefully before use. q In order to ensure proper operation of the CD player, preventative maintenance (cleaning of the - Sharp CD-BA200 | CD-BA200 Operation Manual - Page 18
do to Obtain Service: CD-BA200 Mini Component System (Be sure to have this information available when you need service for your Product.) One (1) year parts and labor from the date of purchase. Non-functional accessories, supplies, and consumable items. At a Sharp Authorized Servicer located in the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
OPERATION MANUAL
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss
or theft, please record below the model number and serial
number which are located on the rear of the unit.
Please retain this information.
Model number
______________________________
Serial number
______________________________
Date of purchase____________________________
Place of purchase
___________________________
MODEL
CD-BA200
MINI COMPONENT SYSTEM
Thank you for purchasing this SHARP product.
To obtain the best performance from this product,
please read this manual carefully.
It will guide you in operating your SHARP product.
CD-BA200 Mini Component System consisting of
CD-BA200 (main unit) and CP-BA200 (speaker system).
Note:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harm-
ful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
●
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and receiver.
●
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
●
Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
CAUTION
RISK OF ELECTRIC SHOCK
DO
NOT OPEN
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
CAUTION:
TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE
COVER (OR
BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSON-
NEL.
The exclamation point within an equi-
lateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servic-
ing) instructions in the literature ac-
companying the appliance.
Caution - use of controls or adjustments or per-
formance of procedures other than those specified
herein may result in hazardous radiation exposure.
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT EX-
POSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Note:
●
It is the intent of Sharp that this product be used in
full compliance with the copyright laws of the United
States and that prior permission be obtained from co-
pyright owners whenever necessary.