Sharp CD-BA200 CD-BA200 Operation Manual - Page 7

Setting The Clock

Get Sharp CD-BA200 PDF manuals and user guides View all Sharp CD-BA200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

SETTING THE CLOCK (Main unit operation) POWER ON/ STAND-BY MEMORY/SET CLOCK TUNING/ TIME ( ) 2 3 4 AM 12:00 AM 0:00 0:00 5 6 7 8 9 In this example, the clock is set for the 12-hour (AM 12:00) system. 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Press the CLOCK button. 3 Within 5 seconds, press the MEMORY/SET button. 4 X W Press the TUNING/TIME ( or ) button to select the time display mode. "AM 12:00" → The 12-hour display will appear. (AM 12:00 - PM 11:59) "AM 0:00" → The 12-hour display will appear. (AM 0:00 - PM 11:59) "0:00" → The 24-hour display will appear. (0:00 - 23:59) q Note that this can only be set when the unit is first installed or it has been reset (see page 15). 5 Press the MEMORY/SET button. 6 X W Press the TUNING/TIME ( or ) button to adjust the hour. X W q Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. q When the 12-hour display is selected, "AM" will change automatically to "PM". 7 Press the MEMORY/SET button. 8 X W Press the TUNING/TIME ( or ) button to adjust the minutes. X W q Press the TUNING/TIME ( or ) button once to advance the time by 1 minute. Hold it down to change the time in 5 minute intervals. q The hour setting will not advance even if minutes advance from "59" to "00". 9 Press the MEMORY/SET button. q The clock starts operating from "0" second. (Seconds are not displayed.) And then the clock display will disappear after a few seconds. To see the time display: Press the CLOCK button. q The time display will appear for about 5 seconds. Note: q The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power cord is disconnected. If this happens, follow the procedure below to change the clock time. To change the clock time: x Press the CLOCK button. y Within 5 seconds, press the MEMORY/SET button. z Perform steps 6 - 9 above. To change the time display mode: x Perform steps 1 - 2 in the section "RESETTING THE MICROCOMPUTER", on page 15. y Perform steps 1 - 9 above. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
SETTING THE CLOCK
POWER
ON/
STAND-BY
CLOCK
MEMORY/SET
TUNING/
TIME
(
)
AM 12:00
AM 0:00
0:00
2
3
4
7
6
5
8
9
In this example, the clock is set for the 12-hour (AM 12:00) sys-
tem.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press the TUNING/TIME (
or
) button to select the time
display mode.
"AM 12:00"
→
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00"
→
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"0:00"
→
The 24-hour display will appear.
(0:00 - 23:59)
●
Note that this can only be set when the unit is first installed
or it has been reset (see page 15).
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME (
or
) button to adjust the hour.
●
Press the TUNING/TIME (
or
) button once to advance
the time by 1 hour. Hold it down to advance continuously.
●
When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
7
Press the MEMORY/SET button.
8
Press the TUNING/TIME (
or
) button to adjust the
minutes.
●
Press the TUNING/TIME (
or
) button once to advance
the time by 1 minute. Hold it down to change the time in 5
minute intervals.
●
The hour setting will not advance even if minutes advance from
"59" to "00".
9
Press the MEMORY/SET button.
●
The clock starts operating from "0" second.
(Seconds are not displayed.)
And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button.
●
The time display will appear for about 5 seconds.
Note:
●
The clock display will flash on and off at the push of the CLOCK
button when the AC power supply is restored after a power
failure occurs or after the AC power cord is disconnected.
If this happens, follow the procedure below to change the clock
time.
To change the clock time:
Press the CLOCK button.
Within 5 seconds, press the MEMORY/SET button.
Perform steps 6 - 9 above.
To change the time display mode:
Perform steps 1 - 2 in the section "RESETTING THE
MICROCOMPUTER", on page 15.
Perform steps 1 - 9 above.
(Main unit operation)
CD-BA200(SEC) TINSE0276AWZZ
6