Sharp DT 200 DT200 Operation Manual - Page 54

Specifications Product type Projector Model DT-200 Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43 DTV 480i/480P/720P/1080i Display method DLP chip, RGB optical shutter method DLP panel Panel size: 0.55Љ Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments Drive method: Digital Light Processing (DLP™) No. of dots: 480,000 dots (800 [H] ‫ ן‬600 [V]) Lens 1-1.2 ‫ ן‬zoom lens, F3.0, f=32.5-44.0 mm Projection lamp 150 W SHP lamp Video input signal RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω terminated S-video input signal 4-pin Mini DIN connector (INPUT 3) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated Component input signal RCA Connector (INPUT 1) Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB: 0.7 Vp-p, 75 Ω terminated PR: 0.7 Vp-p, 75 Ω terminated Component input signal 29-pin connector (INPUT 2) DVI input signal: Digital 250-1,000 mV 50 Ω Analog 0.7 Vp-p 75 Ω Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB: 0.7 Vp-p, 75 Ω terminated PR: 0.7 Vp-p, 75 Ω terminated Component RGB input signal 29-pin connector (INPUT 2) RGB separate/sync on green type analog input: 0-0.7 Vp-p, positive, 75 Ω terminated HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) VERTICAL SYNC. SIGNAL: Same as above Horizontal resolution 520 TV lines (NTSC 3.58 input) RGB input signal 15-PIN MINI D-SUB CONNECTOR (INPUT 2): RGB separate/composite sync/sync on green type analog input: 0-0.7 Vp-p, positive, 75 Ω terminated HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only) VERTICAL SYNC. SIGNAL: Same as above Pixel clock 12-110 MHz Vertical frequency 43-75 Hz Horizontal frequency 15-70 kHz Rated voltage AC 100-240 V Input current 2.1 A Rated frequency 50/60 Hz Power consumption 200 W Heat dissipation 750 BTU/hour Operating temperature 41°F to 95°F (‫ם‬5°C to ‫ם‬35°C) Storage temperature ‫מ‬4°F to 140°F (‫מ‬20°C to ‫ם‬60°C) Cabinet Plastic I/R carrier frequency 38 kHz Dimensions (approx.) 141⁄2Љ (W) ‫ ן‬69⁄16Љ (H) ‫ ן‬127⁄8Љ (D) (368 ‫ ן‬153.8 ‫ ן‬327 mm) (including swivel stand) 141⁄2Љ (W) ‫ ן‬45⁄8Љ (H) ‫ ן‬127⁄8Љ (D) (368 ‫ ן‬118 ‫ ן‬327 mm) (main body only) Weight (approx.) 9.5 lbs. (4.3 kg) (including swivel stand) 8.4 lbs. (3.8kg) (main body only) Supplied accessories Remote control, Two AA size batteries, Power cord, Video cable, Lens cap (attached on the body), Lens cap strap, Operation manual Replacement parts Lamp unit (Lamp/cage module) (BQC-XVZ90+++1), Remote control (RRMCGA088WJSA), AA size batteries, Power cord (QACCDA007WJPZ), Video cable (QCNWGA001WJZZ), Lens cap (CCAPHA004WJ01), Lens cap strap (UBNDT0013CEZZ), Operation manual (TINS-A287WJZZA) This SHARP projector uses a DMD chip. This very sophisticated chip contains 480,000 pixels. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit. If you have any questions about this matter, please call toll free 1-800-BE-SHARP (1800-237-4277). U.S.A. ONLY Specifications are subject to change without notice. Appendix E-53 DT-200(E)#p50_59.p65 53 02.11.21, 11:45 AM