Sharp DV-SL90UM Service Manual - Page 18

FLOW CHART NO.7, Check D1008, C1007, C1038, and

Get Sharp DV-SL90UM PDF manuals and user guides View all Sharp DV-SL90UM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

FLOW CHART NO.6 P-ON+10V (EV+11V) is not outputted. Is 11V voltage supplied to the emitter of Q1002? No Yes Is the voltage of base on Q1002 lower than the No voltage of emitter on Q1002 when turning the power on? Yes Replace Q1002. Check D1030, D1048, C1035, C1048, L1007, and the periphery circuit, and service it if defective. Check Q1016 and PWRCON line and service it if defective. FLOW CHART NO.7 P-ON+5V is not outputted. (EV+11V is outputted normally.) Is the "H" signal inputted into the base of Q1004? No Yes Replace Q1004. Check R1068 and D1046, and service it if defective. FLOW CHART NO.8 P-ON+3.3V is not outputted. (P-ON+10V is outputted normally.) Is 3.3V voltage supplied to the collector of Q1011? No Yes Replace Q1011 or R1067. Check D1008, C1007, C1038, L1007, and the periphery circuit, and service it if defective. FLOW CHART NO.9 EV+5V is not outputted. Is EV+11V outputted normally? Yes Check D1047 and the periphery circuit, and service it if defective. No Refer to "FLOW CHART NO.6" FLOW CHART NO.10 EV+1.2V is not outputted. Is 2.5V voltage supplied to Pin(1) of IC1002? Yes Replace IC1002. No Check D1006, C1014, L1008 and the periphery circuit, and service it if defective. 1-8-2 E592ATS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
1-8-2
E592ATS
FLOW CHART NO.7
P-ON+5V is not outputted. (EV+11V is outputted normally.)
Is the "H" signal inputted into the base of Q1004?
Replace Q1004.
Check R1068 and D1046, and service it if defective.
Yes
No
FLOW CHART NO.8
P-ON+3.3V is not outputted. (P-ON+10V is outputted normally.)
Is 3.3V voltage supplied to the collector of Q1011?
Replace Q1011 or R1067.
Check D1008, C1007, C1038, L1007, and the
periphery circuit, and service it if defective.
Yes
No
FLOW CHART NO.9
EV+5V is not outputted.
Is EV+11V outputted normally?
Check D1047 and the periphery circuit,
and service it if defective.
Refer to "FLOW CHART NO.6"
<P-ON+10V (EV+11V) is not outputted.>
Yes
No
FLOW CHART NO.10
EV+1.2V is not outputted.
Is 2.5V voltage supplied to Pin(1) of IC1002?
Replace IC1002.
Check D1006, C1014, L1008 and the periphery
circuit, and service it if defective.
Yes
No
FLOW CHART NO.6
P-ON+10V (EV+11V) is not outputted.
Is 11V voltage supplied to the emitter of Q1002?
Is the voltage of base on Q1002 lower than the
voltage of emitter on Q1002 when turning the power on?
Replace Q1002.
Check D1030, D1048, C1035, C1048, L1007, and
the periphery circuit, and service it if defective.
Check Q1016 and PWRCON line and service it if
defective.
Yes
Yes
No
No