Sharp DV-SL90UM Service Manual - Page 19

FLOW CHART NO.12, Check D1016, D1017, T1001, and their periphery

Get Sharp DV-SL90UM PDF manuals and user guides View all Sharp DV-SL90UM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

FLOW CHART NO.11 The fluorescent display tube does not light up. No Is 3.3V voltage supplied to Pins(6,24) of IC2001? Yes No Is the voltage of approximately -20V supplied to Pin(15) of IC2001? Yes No Is there 500kHz oscillation at Pin(26) of IC2001? Yes Are the filament voltage supplied between Pins(1, 2) and Pins(29, 30) of the fluorescent No display tube? And the negative voltage applied between these pins and GND? Yes Replace the fluorescent display tube. FLOW CHART NO.12 The key operation is not functioning. Are the contact point and the installation state of the No key switches (SW2101, SW2104-2108) normal? Yes When pressing each switches (SW2101, SW2104- No 2108), do the voltage of each pin of IC2001 (shown below) increase? SW2104, 2106, 2107: IC2001 3PIN SW2101, 2105, 2108: IC2001 4PIN Yes Replace IC2001. FLOW CHART NO.13 No operation is possible from the remote control unit. Operation is possible from the DVD, but no operation is possible from the remote control unit. No Is 5V voltage supplied to Pin(3) terminal of the infrared remote control receiver (RM2001)? Yes Is the "L" pulse sent out Pin(1) terminal of receiver No (RM2001) when the infrared remote control is activated? Yes No Is the "L" pulse supplied to the Pin(22) of CN1001? Yes Replace DVD Main CBA. Check the EV+3.3V line and service it if defective. Check the -FL (-20V) line and service it if defective. Check R2002, IC2001 and their periphery, and service it if defective. Check D1016, D1017, T1001, and their periphery, and service it if defective. No Is -15V voltage supplied to collector of Q1005? Yes Is the "H" signal inputted to base of Q1016? Check PWRCON line, and service No it if defective. Yes Check Q1015, Q1016, D1055, and their periphery, and service it if defective. Re-install the switches (SW2101, SW2104-2108) correctly or replace the poor switch. Check the switches (SW2101, SW2104-2108) and their periphery, and service it if detective. Check EV+5V line and service it if defective. Replace the infrared remote control receiver (RM2001). Or replace the remote control unit. Check the line between Pin(1) terminal of receiver (RM2001) and Pin(22) of CN1001, and service it if defective. 1-8-3 E592ATS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
1-8-3
E592ATS
Yes
No
FLOW CHART NO.12
The key operation is not functioning.
Are the contact point and the installation state of the
key switches (SW2101, SW2104-2108) normal?
When pressing each switches (SW
2101,
SW
2104-
2108
), do the voltage of each pin of IC2001
(shown below) increase?
SW2104, 2106, 2107: IC2001
3PIN
SW2101, 2105, 2108: IC2001
4PIN
Check the switches (
SW2101, SW2104-2108
) and
their periphery, and service it if detective.
No
Re-install the switches (
SW2101, SW2104-2108
)
correctly or replace the poor switch.
Replace IC2001.
Yes
FLOW CHART NO.13
No operation is possible from the remote control unit.
Operation is possible from the DVD, but no
operation is possible from the remote control unit.
Replace the infrared remote control receiver (RM2001).
Or replace the remote control unit.
Check the line between Pin(1) terminal of receiver
(RM2001) and Pin(22) of CN1001, and service it if
defective.
Is the "L" pulse sent out Pin(1) terminal of receiver
(RM2001) when the infrared remote control is activated?
Is the "L" pulse supplied to the Pin(22) of CN1001?
Replace DVD Main CBA.
Is 5V voltage supplied to Pin(3) terminal of
the infrared remote control receiver (RM2001)?
Yes
No
Check EV+5V line and service it if defective.
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
FLOW CHART NO.11
The fluorescent display tube does not light up.
Is 3.3V voltage
supplied to Pins(6,24) of IC2001?
Is the voltage of approximately -20V supplied to
Pin(15) of IC2001?
Is there 500kHz oscillation at Pin(26) of IC2001?
Are the filament voltage supplied between
Pins(1, 2) and Pins(29, 30) of the fluorescent
display tube? And the negative voltage applied
between these pins and GND?
Replace the fluorescent display tube.
Check the EV+3.3V line and service it if defective.
Check the -FL (-20V) line and service it if defective.
Check R2002, IC2001 and their periphery, and
service it if defective.
Check PWRCON
line, and service
it if defective.
Is the "H" signal inputted
to base of Q1016?
Check D1016, D1017, T1001, and their periphery,
and service it if defective.
Is -15V voltage supplied to collector of Q1005?
No
Yes
Yes
No
Check Q1015, Q1016, D1055, and
their periphery, and service it if defective.