Sharp FO 4400 Service Manual - Page 45

SW52 No. 1 ~ No. 8 Reserved Set to "0". SW53 No. 1 ~ No. 8 Reserved Set to "0". SW54 No. 1 ~ No. 8 Reserved Set to "0". SW55 No. 1 ~ No. 8 Reserved Set to "0". SW56 No. 1 ~ No. 8 Reserved Set to "0". SW57 No. 1 ~ No. 8 Reserved Set to "0". SW58 No. 1 ~ No. 8 Reserved Set to "0". SW59 No. 1 ~ No. 8 Reserved Set to "0". SW60 No. 1 ~ No. 8 Reserved Set to "0". SW61 No. 1 F.A.S.T. (RMS) mode Used to determine a function of remote maintenance system (F.A.S.T.). SW61 No. 2 Reserved Set to "0". SW61 No. 3 Verification stamp End stamp: It is set whether the red round mark is stamped at the bottom margin of the document of every page in the memory input mode and document sending mode or not. SW61 No. 4 Day light saving The day light saving function ON/OFF is set. SW61 No. 5, No. 6 Key buzzer volume Key buzzer volume: The sound volume of key inputting buzzer and other buzzers is set. SW61 No. 7, No. 8 Reserved Set to "0". SW62 No. 1, No. 2 Speaker volume Speaker volume: The sound volume of the speaker in the on-hook mode is set. SW62 No. 3 Reserved Set to "1". SW62 No. 4 Reserved Set to "0". SW62 No. 5, No. 6 Ringer volume Ringer volume: The calling sound volume of CI signal receiving is set. SW62 No. 7, No. 8 Reserved Set to "0". SW63 No. 1 Reserved Set to "0". SW63 No. 2 Reserved Set to "1". SW63 No. 3, No. 4 Reserved Set to "0". SW63 No. 5 Reserved Set to "1". SW63 No. 6 Reserved Set to "0". SW63 No. 7 Reserved Set to "1". SW63 No. 8 Reserved Set to "0". SW64 No. 1 Header registration When setting this switch to "1", registering senders is protected. FO-4400U FO-CS1 SW64 No. 2 Reserved Set to "0". SW64 No. 3 Continuous serial polling Turns ON/OFF the continuous polling function. SW64 No. 4, No. 5 Time interval for continuous serial polling Used to set the interval time for continuous serial polling. Normally set to no interval (0 minute). SW64 No. 6, No. 7 Reserved Set to "0". SW64 No. 8 Quick on line function It is selected whether auto dial call is activated in the memory input mode when one document is completely read or when all pages are completely read. SW65 No. 1, No. 2 Cassette selection To set selective modes for detail paper cassettes of the printer. 00: Manual To select detail paper in the first prior- ity cassette in accordance with setting by SW65 3-8 and SW65 1-3. If the de- tail paper in the first priority cassette runs short, the second priority cassette will be used. 01: Automatic 1 To automatically select detail paper with optimum size among the first to third priority cassettes in accordance with setting by SW65 3-8 and SW65 1-3. The optimum paper is selected by every page. If all the cassettes have the same size paper, paper will be selected ac- cording to the cassette priority. 10: Automatic 2 To automatically select detail paper with optimum size among the first to third priority cassettes in accordance with setting by SW65 3-8 and SW65 1-3. At the start of printing, the optimum pa- per is adopted only for the first page. Thereafter the same cassette selected for the first page will be used from the second page and after. If all the cas- settes have the same size paper, pa- per will be selected according to the cassette priority. 11: Except the above 01: the same setting as in the case of Automatic 1 SW65 No. 3 ~ No. 5 The 1st priority cassette To select the first priority cassette. 001: 1st paper feeder (MP-TRAY) 010: 2nd paper feeder 011: 3rd paper feeder Except the above Printing started from the possible paper feeder SW65 No. 6 ~ No. 8 The 2nd priority cassette To select the second priority cassette. 000: Not used (To set in case of using only paper feeder that has been set in the first priority cassette) 001: 1st paper feeder (MP-TRAY) 010: 2nd paper feeder 011: 3rd paper feeder Except the above Not used 2 - 31