Sharp FO 4400 Service Manual - Page 46

FO-4400U FO-CS1 SW66 No. 1 ~ No. 3 The 3rd priority cassette To select the third priority cassette. 000: Not used (To set in case of using only paper feeder that has been set in the first /second priority cassette) 001: 1st paper feeder (MP-TRAY) 010: 2nd paper feeder 011: 3rd paper feeder Except the above Not used SW66 No. 4, No. 5 Cassette selection of separate page The supply origin of a separate page is set. SW66 No. 6 ~ No. 8 Reserved Set to "0". SW67 No.1, No. 2 Power save mode The heater mode of a printer is set. SW67 No. 3 ~ No. 5 Density adjustment of print bias The density of printing is set. It can be also set in the print diagnosis mode. SW67 No. 6, No. 7 Drum life detection The detection mode of Drum life is set. SW67 No. 8 Reserved Set to "0". SW68 No. 1, No. 2 Distinctive ring pattern The distinctive ring patter is set for country. SW68 No. 3 Reserved Set to "0". SW68 No. 4 Reserved Set to "1". SW68 No. 5, No. 6 Reserved Set to "0". SW68 No. 7 Reserved Set to "1". SW68 No. 8 Reserved Set to "0". SW69 No. 1 Reserved Set to "1". SW69 No. 2, No. 3 Reserved Set to "0". SW69 No. 4 Reserved Set to "1". SW69 No. 5 Reserved Set to "0". SW69 No. 6, No. 7 Reserved Set to "1". SW69 No. 8 Reserved Set to "0". SW70 No. 1 Reserved Set to "1". SW70 No. 2 Reserved Set to "0". SW70 No. 3 Reserved Set to "1". SW70 No. 4 ~ No. 7 Reserved Set to "0". SW70 No. 8 Reserved Set to "1". SW71 No. 1, No. 2 The default resolution for copying In case of copying without pressing the RESOLUTION key, resolution will be super fine. SW71 No. 3 Reserved Set to "0". SW71 No. 4 Reserved Set to "1". SW71 No. 5 Reserved Set to "0". SW71 No. 6, No. 7 Picture quality priority mode Used to set the transmission mode which is automatically selected when the MODE key is not pressed. In the copy mode, however, the fine mode is automatically selected unless the MODE key is manually set to another mode. SW71 No. 8 Reserved Set to "0". SW72 No. 1 Reserved Set to "1". SW72 No. 2 Reserved Set to "0". SW72 No. 3 Reserved Set to "1". SW72 No. 4 ~ No. 8 Reserved Set to "0". SW73 No. 1 ~ No. 5 Reserved Set to "0". SW73 No. 6 ~ No. 8 Data reduction Reduction ratio of receiving is set . It can be changed even in the optional mode. To set printing reduction rate of received images. 000: Automatic 100: 100% Except the above 100% SW74 No. 1 Automatic printing of activity report This soft switch is used to select; whether or not to produce the activity report when the memory is full (about 50 items). An activity report can be produced when the following key entry command is made. "FUNC", "2", "#", "START" After producing the activity report, all the data in the memory will be cleared. When the switch function is set to "0" (NO), the data in memory will be deleted from the oldest as it reaches the maximum memory capacity (approx. 50 items). SW74 No. 2 Print out of total time and total number of pages on activity report Used to make a choice of whether the total communication time and pages are recorded in the activity report. SW74 No. 3 Reserved Set to "0". SW74 No. 4 Department function This model has the department audit feature, it has to be set to 1 to utilize this feature. SW74 No. 5 ~ No. 8 Department ID digit Used to set the department ID digit number . When set to "D" , the number is "4" . SW75 No. 1 Copy protect switch When this switch is set to "1", copy is for bidden. SW75 No. 2 Cut-off mode (when copy mode) When in copy, if the scanned data is out of the range of recording, the operator has one of the choices below using the switch. 0: Continue: Data is printed onto the next page with the last 20mm also printed at the beginning of the next page. 1: Cut off: Data scanned out of the limit is cut off (a page is printed.) 2 - 32