Sharp NP-PX2201UL User Manual - NEC - Page 110

Indicator Message Error message, The [CONTROL PANEL

Get Sharp NP-PX2201UL PDF manuals and user guides View all Sharp NP-PX2201UL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

7. Appendix POWER Blue (Light) Blue (Light) STATUS LIGHT Orange (Light) Status varies Off Orange (Light) TEMP. Off Orange (Light) Projector status A button has been pressed while the [CONTROL PANEL LOCK] is activated. ID numbers for the projector and the remote control do not match. Temperature problem (In the "Forced ECO MODE") Procedure The [CONTROL PANEL LOCK] is activated. The setting must be canceled to operate the projector. (→ page 69) Check the control IDs (→ page 67) Ambient temteprature is high. Lower the room temperature. *1 Repetition to light on for 1.5 seconds / off for 7.5 seconds *2 Repetition to light on for 2.5 seconds / off for 0.5 seconds *3 Repetition to light on for 0.5 seconds / off for 0.5 seconds / on for 0.5 seconds / off for 2.5 seconds *4 Repetition to light on for 0.5 seconds / off for 0.5 seconds Indicator Message (Error message) POWER STATUS LIGHT TEMP. Projector status Temperature problem Red Off Off Off (Blink*4) Lens mounting error/Lens problem Red (Blink*4) Red (Light) Red (Light) Off Error requiring service support Red Status Status Off (Light) varies varies *4 Repetition to light on for 0.5 seconds / off for 0.5 seconds Procedure Ambient temperature is out of the operation temperature. Check if any obstruction stays near the exhaust vent. Lens is not mounted properly. Mout it. If the indicator message is remain unchanged even if the lens is mounted properly, contact your dealer. Contact your dealer or service personnel. Make sure to check and inform indicator status for asking to repair. • When the thermal protector is activated: When inside temperature of the projector becomes too high or low, the POWER indicator start to red blink in a short cycle. After this happened, the thermal protector will activate and the projector may be turned off. In this case, please take the below measures: - Pull out the power plug from the wall inlet. - Place the projector in cool place if it has been placed in high ambient temperature. - Clean the exhaust vent if dust has accumulated on. - Leave the projector for about one hour until inside temperature gets lower. 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
90
7. Appendix
POWER
STATUS
LIGHT
TEMP.
Projector status
Procedure
A button has been pressed
while the [CONTROL PANEL
LOCK] is activated.
The [CONTROL PANEL
LOCK] is activated. The
setting must be canceled to
operate the projector. (
→
page
69
)
Blue
(Light)
Orange
(Light)
Status varies
Off
ID numbers for the projector
and the remote control do not
match.
Check the control IDs (
→
page
67
)
Temperature problem (In the
“Forced ECO MODE”)
Ambient temteprature is high.
Lower the room temperature.
Blue
(Light)
Off
Orange
(Light)
Orange
(Light)
*1 Repetition to light on for 1.5 seconds / off for 7.5 seconds
*2 Repetition to light on for 2.5 seconds / off for 0.5 seconds
*3 Repetition to light on for 0.5 seconds / off for 0.5 seconds / on for 0.5 seconds / off for 2.5 seconds
*4 Repetition to light on for 0.5 seconds / off for 0.5 seconds
Indicator Message (Error message)
POWER
STATUS
LIGHT
TEMP.
Projector status
Procedure
Temperature problem
Ambient temperature is out of the
operation temperature. Check if any
obstruction stays near the exhaust
vent.
Red
(Blink*
4
)
Off
Off
Off
Lens mounting error/Lens problem
Lens is not mounted properly. Mout it.
If the indicator message is remain un-
changed even if the lens is mounted
properly, contact your dealer.
Red
(Blink*
4
)
Red
(Light)
Red
(Light)
Off
Error requiring service support
Contact your dealer or service person-
nel. Make sure to check and inform
indicator status for asking to repair.
Red
(Light)
Status
varies
Status
varies
Off
*4 Repetition to light on for 0.5 seconds / off for 0.5 seconds
•
When the thermal protector is activated:
When inside temperature of the projector becomes too high or low, the POWER indicator start to red blink in a short cycle. After
this happened, the thermal protector will activate and the projector may be turned off.
In this case, please take the below measures:
-
Pull out the power plug from the wall inlet.
-
Place the projector in cool place if it has been placed in high ambient temperature.
-
Clean the exhaust vent if dust has accumulated on.
-
Leave the projector for about one hour until inside temperature gets lower.