Sharp PG-C30XE Operation Manual - Page 20

Using the Adjustment Foot, Reversed Image Setup, Ceiling-mount Setup

Get Sharp PG-C30XE - Notevision XGA LCD Projector PDF manuals and user guides View all Sharp PG-C30XE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Setting up the Screen 1 3 Foot release Using the Adjustment Foot You can adjust the height of the image by raising the projector with the foot release. 1 Press the foot release and lift the projector to the desired angle. (Adjustable up to approximately 5° from the standard position.) 2 Remove your hand from the foot release. Once the adjustment foot has locked in position, release the projector. 3 If the screen is at an angle, the adjuster can be used to adjust the angle of the image. (Adjustable up to approximately 1° from the original position.) Returning the projector to its original position While holding the projector, press the foot release and slowly lower the projector to its original position. • When an adjustment is made, the image may become distorted (keystoned), depending on the relative positions of the projector and the screen. CAUTION • Do not press the foot release when the adjustment foot is extended without firmly holding the projector. • Do not hold the lens when lifting or lowering the projector. • When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. Reversed Image Setup Rear projection • Place a translucent screen between the projector and the audience. • Use the projector's menu system to reverse the projected image. (See page 42 for use of this function.) Projection using a mirror • When the distance between the projector and screen is not sufficient for normal rear projection, you can use a mirror to reflect the image onto the screen. • Place a mirror (normal flat type) in front of the lens. • Project the normal image onto the mirror. • The image reflected from the mirror is projected onto the translucent screen. Operation • Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all feet flat and level. CAUTION • When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of the audience. Ceiling-mount Setup • It is recommended that you use the optional Sharp ceilingmount bracket for this installation. • Before mounting the projector, contact your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center to obtain the recommended ceiling-mount bracket (sold separately). (AN-XGCM51 ceiling-mount bracket, ANEP101AP extension tube for AN-XGCM51.) • When the projector is in the inverted position, use the upper edge of the screen as the base line. • Use the projector's menu system to select the appropriate projection mode. (See page 42 for use of this function.) E-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
E-19
Operation
Setting up the Screen
Using the Adjustment Foot
You can adjust the height of the image by raising the
projector with the foot release.
1
Press the foot release and lift the projector to the
desired angle. (Adjustable up to approximately
5
°
from the standard position.)
2
Remove your hand from the foot release. Once
the adjustment foot has locked in position, release
the projector.
3
If the screen is at an angle, the adjuster can be
used to adjust the angle of the image. (Adjustable
up to approximately 1
°
from the original position.)
1
3
Foot release
Returning the projector to its original position
While holding the projector, press the foot release and slowly lower the projector to its original position.
•
When an adjustment is made, the image may become distorted (keystoned), depending on the relative positions of the projector and the
screen.
CAUTION
•
Do not press the foot release when the adjustment foot is extended without firmly holding the projector.
•
Do not hold the lens when lifting or lowering the projector.
•
When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the
projector.
•
Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all feet flat and level.
Reversed Image Setup
Projection using a mirror
•
When the distance between the projector and screen
is not sufficient for normal rear projection, you can
use a mirror to reflect the image onto the screen.
•
Place a mirror (normal flat type) in front of the lens.
•
Project the normal image onto the mirror.
•
The image reflected from the mirror is projected onto
the translucent screen.
Rear projection
•
Place a translucent screen between the projector and
the audience.
•
Use the projector
’
s menu system to reverse the
projected image. (See page 42 for use of this
function.)
CAUTION
•
When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount Setup
•
It is recommended that you use the optional Sharp ceiling-
mount bracket for this installation.
•
Before mounting the projector, contact your nearest Authorized
Sharp Industrial LCD Products Dealer or Service Center to
obtain the recommended ceiling-mount bracket (sold
separately). (AN-XGCM51 ceiling-mount bracket, AN-
EP101AP extension tube for AN-XGCM51.)
•
When the projector is in the inverted position, use the upper
edge of the screen as the base line.
•
Use the projector
’
s menu system to select the appropriate
projection mode. (See page 42 for use of this function.)