Sharp PN-R903 Operation Manual - Page 44

Controlling the Monitor with a PC (RS-232C) Initialization/Functional Restriction Setting (FUNCTION) menu Function Command Direction Parameter Reply Control/Response contents * ALL RESET RSET W 0-1 0: ALL RESET 1, 1: ALL RESET 2 - ADJUSTMENT LOCK ALCK WR 0-2 0-2 0: OFF, 1:ON1, 2:ON2 ADJUSTMENT LOCK TARGET ALTG WR 0-2 0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH OSD DISPLAY LOSD WR 0-2 0-2 0: ON1, 1: OFF, 2: ON2 LED OFLD WR 0-1 0-1 0: ON, 1: OFF TEMPERATURE ALERT TALT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED ○ POWER BUTTON PBTN WR 0-1 0-1 0: MONITOR, 1: CONTROLLER CONTROLLER INPUT PCIP WR 0-4 0-4 0: D-SUB, 1: DisplayPort, 2: HDMI1, 3: HDMI2, 4: DVI-I ("ERR" when MONITOR is selected for POWER BUTTON.) STATUS ALERT SALT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED Others Function SCREEN SIZE (PC) SCREEN SIZE (AV) VOLUME MUTE INFORMATION MODEL SERIAL NO TEMPERATURE SENSOR Command Direction WIDE WR WIDE WR VOLM WR MUTE WR INF1 R SRNO R DSTA R Parameter 1-5 1-5 0-31 0-1 Temperature acquisition ERRT R CAUSE OF LAST STANDBY MODE STCA W 0 R Reply Control/Response contents * 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot ○ 0-31 0-1 0: OFF, 1: ON - Value Value ● 0 Internal temperature normal 1 Internal temperature abnormal has occurred and the monitor is in standby mode 2 Internal temperature abnormal occurred (To delete the information of temperature abnormal, turn off the main power.) ● 3 Internal temperature abnormal has occurred and backlight brightness is dimmed 4 Temperature sensor abnormal Value Temperature at temperature sensors 1 through 6 are returned in the following forms: [Sensor 1], [Sensor 2], [Sensor 3], [Sensor 4], [Sensor 5], [Sensor 6] ○ Indicates a temperature sensor abnormality when "126" is returned. Initialization 0 No detectable error has occurred 1 Standby mode by POWER button 2 Main power off by the main power switch 3 Standby mode by RS-232C or LAN ● 4 Input signal waiting mode by No Signal 6 Standby mode by abnormal temperature 8 Standby mode by SCHEDULE setting 20 Standby mode by OFF IF NO OPERATION setting Commands for setting of the GAMMA user data Function Command Direction Parameter Reply Control/Response contents * RED GAMMA DATA TRANSFER UGRW W aaxxxx ··· xxxxcc aa: Block number GREEN GAMMA DATA TRANSFER BLUE GAMMA DATA TRANSFER UGGW W UGBW W (xxxx: 32 pieces) aa: 01-16 xxxx: 0000-1023 xxxx: 32 pieces of user data cc: Checksum (ASCII data) of the block number and user data cc: 00-FF RED GAMMA DATA READ UGRR W 1-16 xxxx ··· xxxx xxxx: User data of 32 pieces ○ GREEN GAMMA DATA READ BLUE GAMMA DATA READ UGGR W UGBR W 1-16 (xxxx: 32 pieces) 1-16 xxxx: 0000-1023 USER DATA INITIALIZE UGRS W 0 Initialize the user data. USER DATA SAVE UGSV W 0 Save the user data in the monitor. E 44