Sharp XG-MB70X XG-MB70X Operation Manual - Page 69

At least 10 minutes.

Get Sharp XG-MB70X - XGA DLP Projector PDF manuals and user guides View all Sharp XG-MB70X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Maintenance indicator Normal Abnormal Temperature warning indicator Off Red on (Standby) Problem The internal temperature is abnormally high. Cause Possible solution • Blocked air intake • Relocate the projector to an area with proper ventilation (see page 7). • Take the projector to your nearest • Cooling fan break- Sharp Authorized Projector Dealer down or Service Center (see page 72) • Internal circuit failure for repair. • Clogged air intake • Clean the exhaust and intake vents. (See page 63.) Lamp indicator Green on Green blinks when the lamp is warming up or shutting down. Red on Red on (Standby) The lamp does not illuminate. Time to change the lamp. The lamp does not illuminate. • The lamp is shut down abnormally. • Disconnect the power cord from the AC outlet, and then connect it again. • Carefully replace the lamp. (See • Remaining lamp life page 67.) becomes 5% or less. • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 72) • Burnt-out lamp for repair. • Lamp circuit failure • Please exercise care when replacing the lamp. Info • If the temperature warning indicator illuminates and the projector enters the standby mode, check whether any of the ventilation holes are blocked (page 7) and then try turning the power back on. Wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.) • If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. • Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds. Appendix -65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
-65
Appendix
Maintenance indicator
Problem
Cause
Possible solution
Temperature
warning
indicator
Normal
Abnormal
Off
Red on
(Standby)
The internal
temperature is
abnormally high.
Abnormal
•
Blocked air intake
•
Relocate the projector to an area
with proper ventilation (see page
7
).
•
Cooling fan break-
down
•
Internal circuit failure
•
Clogged air intake
•
Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page
72
)
for repair.
•
Clean the exhaust and intake
vents. (See page
63.
)
Lamp
indicator
Red on
(Standby)
The lamp does
not illuminate.
•
Burnt-out lamp
•
Lamp circuit failure
•
Carefully replace the lamp. (See
page
67
.)
•
Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page
72
)
for repair.
•
Please exercise care when
replacing the lamp.
Red on
Time to change
the lamp.
•
Remaining lamp life
becomes 5% or less.
Green on
Green blinks
when the lamp
is warming up
or shutting
down.
Info
•
If the temperature warning indicator illuminates and the projector enters the standby mode, check whether
any of the ventilation holes are blocked (page
7
) and then try turning the power back on. Wait until the
projector has cooled down completely before plugging in the power cord and turning the power back on.
(At least 10 minutes.)
•
If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
•
Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan
is running. The cooling fan runs for about 90 seconds.
The lamp does
not illuminate.
•
The lamp is shut
down abnormally.
•
Disconnect the power cord from
the AC outlet, and then connect it
again.