Sharp XV-Z3000 XV-Z3000 Operation Manual - Page 56

Removing and Installing the Lamp Unit, Lamp Unit - an 100lp

Get Sharp XV-Z3000 - SharpVision WXGA DLP Projector PDF manuals and user guides
UPC - 074000364820
View all Sharp XV-Z3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Removing and Installing the Lamp Unit Warning! • The lamp unit becomes very hot while the projector is operating. Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury. Optional accessory Lamp unit AN-100LP Info • Make sure that you remove the lamp unit by the handle. Do not touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. 1 Press SSTANDBY/ON on the projector or aSTANDBY on the remote control to put the projector into standby mode. • Wait until the cooling fan stops. STANDBY/ON button AC socket 2 Disconnect the power cord. • Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). 3 Remove the lamp unit cover. • Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2). 1 2 User service screw (for lamp unit cover) Appendix 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
Appendix
55
Removing and Installing the
Lamp Unit
•
Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of
the lamp unit or the inside of the projector.
•
To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps
below.
•
Do not loosen other screws except for the
lamp unit cover and lamp unit.
Press
S
STANDBY/ON on the pro-
jector or
a
STANDBY on the re-
mote control to put the projector
into standby mode.
• Wait until the cooling fan stops.
Warning!
•
The lamp unit becomes very hot while the pro-
jector is operating. Do not remove the lamp
unit from the projector right after use. The lamp
and parts around the lamp will be very hot and
may cause burns or injury.
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
Remove the lamp unit cover.
• Turn the projector over. Loosen the user
service screw (
1
) that secures the lamp
unit cover. Remove the lamp unit cover
(
2
).
1
2
Lamp unit
AN-100LP
Info
Optional
accessory
AC socket
User service screw
(for lamp unit cover)
1
2
3
STANDBY/ON button