Sharp XVZ12000U Operation Manual - Page 91

For SHARP Assistance U.S.A only

Get Sharp XVZ12000U - DLP Projector - 900 ANSI Lumens PDF manuals and user guides
UPC - 074000364028
View all Sharp XVZ12000U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Troubleshooting Problem Picture is green on INPUT 1 or 2 COMPO- NENT. Picture is pink (no green) on INPUT 1 or 2 RGB. Picture is dark. Picture is too bright and whitish. A response code cannot be received when the projector was attempted to be controlled using RS-232C commands from a computer during standby. Check • Change the input signal type setting. • The lamp indicator is blinking in red. Replace the lamp. • Picture adjustments are incorrectly set. • In the case of transmitting RS-232C commands from a computer during standby, it takes a maximum of 30 seconds for the computer to receive the response code. Set the response code waiting time of the computer to 30 seconds or more. Page 69 78 47 84 For SHARP Assistance (U.S.A only) If you encounter any problems during setup or operation of this projector, first refer to the "Troubleshooting" section on pages 89 and 90. If this operation manual does not answer your question, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an email at [email protected] . Our World Wide Web address is http://www.sharpusa.com/ . -90 XV_Z12000_E_US_p89_96.p65 90 03.9.24, 2:10 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
-90
Check
Problem
Page
Troubleshooting
For SHARP Assistance (U.S.A only)
If you encounter any problems during setup or operation of this projector, first refer to the
“
Trouble-
shooting
”
section on pages
89
and
90
. If this operation manual does not answer your question,
please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance.
Or, send us an e-
Our World Wide Web address is http://www.sharpusa.com/ .
•
Change the input signal type setting.
69
•
The lamp indicator is blinking in red. Replace the lamp.
78
•
Picture adjustments are incorrectly set.
47
•
In the case of transmitting RS-232C commands from a computer
84
during standby, it takes a maximum of 30 seconds for the
computer to receive the response code. Set the response code
waiting time of the computer to 30 seconds or more.
Picture is green on
INPUT 1 or 2 COMPO-
NENT.
Picture is pink (no green)
on INPUT 1 or 2 RGB.
Picture is dark.
Picture is too bright and
whitish.
A response code cannot
be received when the
projector was attempted
to be controlled using
RS-232C commands
from a computer during
standby.
XV_Z12000_E_US_p89_96.p65
03.9.24, 2:10 PM
90