Singer SE300 Legacy Instruction Manual and Troubleshooting Guide - Page 14

14

A

B

T

HREAD

T

ENSION

(B)

This machine sets the thread tension automatically when

pattern is selected. However, you can change the thread

tension, as follows.

To increase the upper thread tension, press the

+ button.

To decrease the upper thread tension, press the

– button.

If you change from pre-set, number will be highlighted.

<RX F´Q VW´³W VHZLQJ Z¶LOH LQ W¶LV PRGH ´QG F¶´QJH WHQVLRQ

while sewing.

7R ³HWX³Q WR S³HYLRXV VF³HHQÂ VWRS VHZLQJ ´QG S³HVV W¶H 6HWWLQJ

Button again.

When another stitch pattern is selected, thread tension will

return to pre-set.

3UHVHW 7KUHDG 7HQVLRQ

Upper and bobbin thread will lock approximately in the middle

of fabric.

S

ETTING

OF

THE

S

TITCH

P

ATTERN

<RX³ P´F¶LQH ZLOO ´XWRP´WLF´OO\ VHOHFW RSWLPXP VHWWLQJV IR³

H´F¶ VWLWF¶µ <RX F´Q P´¹H ´GMXVWPHQWV WR HYH³\ VWLWF¶ ´V

desired. Adjusted settings only affect the selected stitch and

will be reset to default when another stitch is selected. Adjusted

settings are not automatically saved when the machine is

turned off.

Iµ

6WLWF¶ :LGW¶Ì1HHGOH 3RVLWLRQ

Increase or decrease the stitch width using + and - buttons.

)R³ VW³´LJ¶W VWLWF¶HVÂ XVH è ´QG Æ WR PRYH W¶H VWLWF¶ SRVLWLRQ

left or right.

When a setting is changed, the numbers will be highlighted.

When trying to exceed minimum or maximum settings, a

warning sound will be heard.

Jµ

6WLWF¶ /HQJW¶Ì'HQVLW\

Increase or decrease the stitch length using + and -

buttons.

:¶HQ VHZLQJ VWLWF¶HV I³RP W¶H 6´WLQ F´WHJR³\ »VWLWF¶HV

ÜÝßÆÜßÞÁÂ XVH W¶H è ´QG Æ EXWWRQV WR LQF³H´VH R³ GHF³H´VH

stitch density.

This may be necessary depending on the

type of thread being used.

When a satin stitch is selected, the icon changes to show

that stitch density is active instead of stitch length.

h.

Width Mirroring

%\ S³HVVLQJ W¶H :LGW¶ 0L³³R³ EXWWRQÂ VWLWF¶ ZLOO ÀLS I³RP OHIW

to right.

i.

Length Mirroring

%\ S³HVVLQJ W¶H /HQJW¶ 0L³³R³ EXWWRQÂ VWLWF¶ ZLOO ÀLS I³RP WRS

to bottom.

When mirroring is active, the button will be highlighted. If

mirroring is not available, a warning sound will be heard.

j.

Elongation

6WLWF¶HV LQ W¶H (ORQJ´WLRQ F´WHJR³\ »VWLWF¶HV ÜßÝÆÜáßÁ F´Q

be elongated. The entire stitch will be longer but the density

will remain the same. Press the Alt button to show the

elongation setting instead of density for satin stitches. The

density changes to show an elongation symbol. Increase or

decrease the elongation of the satin stitch using the + and -

buttons.

f

h

g

i

j

MACHINE SETTINGS

S

ETTING

B

UTTON

(A)

Before or during the sewing process, you can adjust the

VHWWLQJV E\ S³HVVLQJ W¶H 6HWWLQJ %XWWRQµ

7¶H 6HWWLQJ 6F³HHQ ZLOO ´SSH´³µ

This screen is scrolled by pressing the right side arrow buttons.

3³HVVLQJ W¶H 6HWWLQJ %XWWRQ ´J´LQÂ P´F¶LQH ZLOO ³HWX³Q WR

previous screen.

NOTE:

All settings except for thread tension will remain until you

change them. Thread tension will return to pre-set when you

change the pattern. Default settings will differ depending on the

stitch selected.

S

EWING

P

REPARATION

8SSHU 7KUHDG 7HQVLRQ 7RR 7LJKW

Bobbin thread will appear on the top side of the fabric.

Decrease upper thread tension.

Singer SE300 Legacy Instruction Manual and Troubleshooting Guide - Page 14

Machine Settings

Page 14 highlights