Singer SE300 Legacy Instruction Manual and Troubleshooting Guide - Page 8

Changing The Presser Foot

Get Singer SE300 Legacy PDF manuals and user guides View all Singer SE300 Legacy manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

The presser foot must be changed according to the stitch RUWHFKQLTXH\RXVHZ,QIRUPDWLRQRQVHZLQJDQGVHZLQJ WHFKQLTXHVEHJLQVRQSDJH ACCESSORIES CAUTION  7RSUHYHQWDFFLGHQWV  7XUQRIIWKHSRZHUVZLWFKEHIRUH\RXFKDQJHWKH SUHVVHUIRRW CHANGING THE PRESSER FOOT 1. Turn the hand wheel toward you until the needle is at its highest position. 2. Raise the presser foot lifter. REMOVING THE PRESSER FOOT HOLDER When attaching presser feet that have their own shank, or when cleaning the machine, you should remove the presser foot holder. 1. Remove the presser foot. 2. Loosen the presser foot screw and remove the presser foot holder. 3. Remove the presser foot by pushing the presser foot release lever toward you. 4. Place desired foot with its pin directly under the slot in presser foot holder. 3. To replace the holder, pull up the holder as far as it will go from bottom of presser bar. 4. Tighten the presser foot screw securely using the screwdriver. 5. Lower the presser foot lifting lever and the presser foot will snap into place. NOTE: This sewing machine is a low shank model. When VKRSSLQJIRURSWLRQDO6,1*(5SUHVVHUIHHWDQGDFFHVVRULHV make sure they are designed for low shank models. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
8
The presser foot must be changed according to the stitch
R³ WHF¶QLTXH \RX VHZµ ¸QIR³P´WLRQ RQ VHZLQJ ´QG VHZLQJ
WHF¶QLTXHV EHJLQV RQ S´JH âܵ
CHANGING THE PRESSER FOOT
1.
Turn the hand wheel toward you until the needle is at its
highest position.
2.
Raise the presser foot lifter.
3.
Remove the presser foot by pushing the presser foot
release lever toward you.
4.
Place desired foot with its pin directly under the slot in
presser foot holder.
5.
Lower the presser foot lifting lever and the presser foot will
snap into place.
R
EMOVING
THE
P
RESSER
F
OOT
H
OLDER
When attaching presser feet that have their own shank, or
when cleaning the machine, you should remove the presser
foot holder.
1.
Remove the presser foot.
2.
Loosen the presser foot screw and remove the presser foot
holder.
3.
To replace the holder, pull up the holder as far as it will go
from bottom of presser bar.
4.
Tighten the presser foot screw securely using the
screwdriver.
A
CCESSORIES
CAUTION
7R SUHYHQW DFFLGHQWV²
7XUQ RII WKH SRZHU VZLWFK EHIRUH \RX FKDQJH WKH
SUHVVHU IRRW´
NOTE:
This sewing machine is a low shank model.
When
V¶RSSLQJ IR³ RSWLRQ´O 6¸1*(5 S³HVVH³ IHHW ´QG ´FFHVVR³LHVÂ
make sure they are designed for low shank models.