Smeg STU8222 User manual - Page 57

E1, E2, E3, E4, E8

Get Smeg STU8222 PDF manuals and user guides View all Smeg STU8222 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

User instructions E7 E8 E9 E11 FAULT DESCRIPTION Turbine flow-regulator malfunction (for the relevant models only) The appliance is not able to "measure" the amount of water loaded accurately. Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. Alternate washing system malfunction Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. Water intake system malfunction Contact the after-sales service. Wash motor pump does not work Light off Light on Light flashing If an alarm occurs the appliance interrupts the program in progress and signals a fault.  Alarms E1, E2, E3, E4, E8 and E9 interrupt the current program immediately.  The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program.  The alarm E7 is visualized at the end of the cycle that comes, however, brought to the end since the operation of the dishwasher is not harmed.  E11: Contact the after-sales service. To "reset" an alarm is necessary:  Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again. If the malfunction persists, contact your authorised Service Centre. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
User instructions
57
FAULT
DESCRIPTION
E7
Turbine flow-regulator malfunction
(for the relevant models only)
The appliance is not able to "measure" the amount
of water loaded accurately. Interrupt the program
and
switch
off
the
dishwasher.
Switch
the
dishwasher back on, program it again and start the
washing cycle. If the problem persists, contact the
after-sales service.
E8
Alternate washing system malfunction
Interrupt the program and switch off the dishwasher.
Switch the dishwasher back on, program it again and
start the washing cycle. If the problem persists, contact
the after-sales service.
E9
Water intake system malfunction
Contact the after-sales service.
E11
Wash motor pump does not work
Light off
Light on
Light flashing
If an alarm occurs the appliance interrupts the program in progress and
signals a fault.
Alarms
E1, E2, E3, E4, E8
and
E9
interrupt the current program
immediately.
The
E5
,
E6
alarms interrupts the running program once the cause is
resolved, it will bring bach the execution of the program.
The alarm
E7
is visualized at the end of the cycle that comes,
however, brought to the end since the operation of the dishwasher is
not harmed.
E11:
Contact the after-sales service.
To “reset” an alarm is necessary:
Open and close the door, or turn off and on the machine. At this point
is possible to program the dishwasher again.
If the malfunction persists, contact your authorised Service Centre.