Sony CMT-U1BT Operating Instructions - Page 24

Others, Troubleshooting - problems

Get Sony CMT-U1BT - Micro Hi-fi Component System PDF manuals and user guides View all Sony CMT-U1BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Others Troubleshooting 1 Make sure the power cord and speaker cords are correctly and firmly connected. 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. If the STANDBY indicator flashes Immediately unplug the power cord, and check the following item. • If your system has a voltage selector, is the voltage selector set to the correct voltage? • Are you using only the supplied speakers? • Is anything blocking the ventilation holes on the top or back of the system? After the STANDBY indicator  stops flashing, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. General The display starts flashing as soon as you plug in the power cord even though you have not turned on the system. • Press DISPLAY  while the system is off. The demonstration disappears. Sound comes from one channel, or the left and right volumes are unbalanced. • Place the speakers as symmetrically as possible. • Connect only the supplied speakers. Severe hum or noise. • Move the system away from sources of noise. • Connect the system to a different wall socket. • Install a noise filter (available separately) to the power cord. The remote does not function. • Remove any obstacles between the remote and the remote sensor  on the unit, and position the unit away from fluorescent lights. • Point the remote at the system's sensor. • Move the remote closer to the system. CD/"ATRAC"/MP3 player The sound skips, or the disc will not play. • Wipe the disc clean, and replace it. • Move the system to a location away from vibration (for example, on top of a stable stand). • Move the speakers away from the system, or place them on separate stands. At high volume, speaker vibration may cause the sound to skip. Play does not start from the first track. • Press PLAY MODE  repeatedly until both "PGM" and "SHUF" disappear to return to normal play. Starting playback takes more time than usual. • The following discs take a longer time to start playback. - a disc recorded with a complicated tree structure. - a disc recorded in multisession mode. - a disc that has not been finalized (a disc to which data can be added). - a disc that has many folders. 24GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
±³
GB
Others
Troubleshooting
1
Make sure the power cord and speaker
cords are correctly and firmly connected.
2
Find your problem in the checklist below,
and take the indicated corrective action.
If the issue persists, contact your nearest
Sony dealer.
If the STANDBY indicator flashes
Immediately unplug the power cord, and
check the following item.
• If your system has a voltage selector, is the
voltage selector set to the correct voltage?
• Are you using only the supplied speakers?
• Is anything blocking the ventilation holes
on the top or back of the system?
Aſter the STANDBY indicator
stops
flashing, reconnect the power cord, and turn
on the system. If the issue persists, contact
your nearest Sony dealer.
General
The display starts flashing as soon as you
plug in the power cord even though you
have not turned on the system.
• Press DISPLAY
while the system is off.
°e demonstration disappears.
Sound comes from one channel, or the left
and right volumes are unbalanced.
• Place the speakers as symmetrically as
possible.
• Connect only the supplied speakers.
Severe hum or noise.
• Move the system away from sources of noise.
• Connect the system to a different wall socket.
• Install a noise filter (available separately) to
the power cord.
The remote does not function.
• Remove any obstacles between the remote
and the remote sensor
on the unit, and
position the unit away from fluorescent
lights.
• Point the remote at the system’s sensor.
• Move the remote closer to the system.
CD/“ATRAC”/MP3 player
The sound skips, or the disc will not play.
• Wipe the disc clean, and replace it.
• Move the system to a location away from
vibration (for example, on top of a stable
stand).
• Move the speakers away from the system,
or place them on separate stands. At high
volume, speaker vibration may cause the
sound to skip.
Play does not start from the first track.
• Press PLAY MODE
repeatedly until both
“PGM” and “SHUF” disappear to return to
normal play.
Starting playback takes more time than
usual.
• °e following discs take a longer time to start
playback.
– a disc recorded with a complicated tree structure.
– a disc recorded in multisession mode.
– a disc that has not been finalized (a disc to which
data can be added).
– a disc that has many folders.