Sony DVPNS61 Service Manual - Page 15
TV Virtual Surround, Settings, Changing the Angles, Displaying the Subtitles
View all Sony DVPNS61 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
DVP-NS36/NS37/NS45P/NS55P/NS61P/NS63P Sound Adjustments Notes • While playing a Super VCD on which the audio track 2 is not recorded, no sound will come out when you select "2:STEREO," "2:1/L," or "2:2/R." • When playing DVD-RW/DVD-R in VR mode: If you connect to an AV amplifier (receiver) using the DIGITAL OUT (COAXIAL or OPTICAL) jack and want to switch between the sound tracks, set "DOLBY DIGITAL" to "D-PCM" in "AUDIO SETUP." Checking the audio signal format You can check the audio signal format by pressing /AUDIO repeatedly during playback. The format of the current audio signal (Dolby Digital, DTS, PCM, etc.) appears as shown below. ◆When playing a DVD VIDEO Example: Dolby Digital 5.1 ch Rear (L/R) About audio signals Audio signals recorded in a disc contain the sound elements (channels) shown below. Each channel is output from a separate speaker. • Front (L) • Front (R) • Centre • Rear (L) • Rear (R) • Rear (Monaural): This signal can be either the Dolby Surround Sound processed signals or the Dolby Digital sound's monaural rear audio signals. • LFE (Low Frequency Effect) signal Notes • If "DTS" is set to "OFF" in "AUDIO SETUP" (page 67) the DTS track selection option will not appear on the screen even if the disc contains DTS tracks. • MPEG audio signals with more than two channels will appear as shown above (3/2.1, 2/1), but only the Front (L) and Front (R) signals will be output from your two front speakers. 1:ENGLISH DOLBY DIGITAL 3 / 2 .1 Front (L/R) LFE (Low Frequency + Centre Effect) Example: Dolby Digital 3 ch 2:SPANISH DOLBY DIGITAL 2 / 1 Front (L/R) Rear (Monaural) ◆When playing a DivX video file on a DATA CD or a DATA DVD Example: MP3 audio 1: MP3 128k Bit rate 39 ◆TVS WIDE Creates five sets of virtual rear speakers from the sound of the front speakers (L, R) without using actual rear speakers (shown below). This mode is effective when the distance between the front L and R speakers is short, such as with built-in speakers on a stereo TV. TV Notes • When the playing signal does not contain a signal for the rear speakers, the surround effects cannot be heard. • When you select one of the TVS modes, turn off the surround setting of the connected TV or amplifier (receiver). • Make sure that your listening position is between and at an equal distance from your speakers, and that the speakers are located in similar surroundings. • Not all discs will respond to the "TVS NIGHT" function in the same way. • The TVS effects do not work when using the Fast Play or Slow Play functions, even though you can change the TVS modes. ◆TVS NIGHT Large sounds, such as explosions, are suppressed, but the quieter sounds are unaffected. This feature is useful when you want to hear the dialogue and enjoy the surround sound effects of "TVS WIDE" at low volume. ◆TVS STANDARD Creates three sets of virtual rear speakers from the sound of the front speakers (L, R) without using actual rear speakers (shown below). Use this setting when you want to use TVS with 2 separate speakers. L R Sound Adjustments L: Front speaker (left) R: Front speaker (right) : Virtual speaker TV Virtual Surround Settings (TVS) When you connect a stereo TV or 2 front speakers, TVS (TV Virtual Surround) lets you enjoy surround sound effects by using sound imaging to create virtual rear speakers from the sound of the front speakers (L: left, R: right) without using actual rear speakers. TVS was developed by Sony to produce surround sound for home use using just a stereo TV. This only works when playing a multichannel Dolby audio soundtrack. Furthermore, if the player is set up to output the signal from the DIGITAL OUT (OPTICAL or COAXIAL) jack, the surround effect will only be heard when "DOLBY DIGITAL" is set to "DPCM" and "MPEG" is set to "PCM" in "AUDIO SETUP" (page 67). 2 Press SUR repeatedly to select one of the TVS sounds. See the explanations given for each item in the following section. • TVS DYNAMIC THEATER • TVS DYNAMIC • TVS WIDE • TVS NIGHT • TVS STANDARD To cancel the setting Select "OFF" in step 2. ◆TVS DYNAMIC THEATER Creates one set of LARGE virtual rear speakers and virtual subwoofer from the sound of the front speakers (L, R) without using actual rear speakers and subwoofer (shown below). This mode is effective when the distance between the front L and R speakers is short, such as with built-in speakers on a stereo TV. TV Sub woofer SUR 1 Press SUR during playback. The following display appears. TVS DYNAMIC THEATER ◆TVS DYNAMIC Creates one set of virtual rear speakers from the sound of the front speakers (L, R) without using actual rear speakers (shown below). This mode is effective when the distance between the front L and R speakers is short, such as with built-in speakers on a stereo TV. TV 40 Enjoying Movies Changing the Angles If various angles (multi-angles) for a scene are recorded on the DVD VIDEO, " " appears in the front panel display. This means that you can change the viewing angle. Displaying the Subtitles If subtitles are recorded on the discs, you can change the subtitles or turn them on and off whenever you want while playing a DVD. /SUBTITLE /ANGLE 1 Press /ANGLE during playback. The number of the angle appears on the display. 2 2 Press /ANGLE repeatedly to select an angle number. The scene changes to the selected angle. Note Depending on the DVD VIDEO, you may not be able to change the angles even if multi-angles are recorded on the DVD VIDEO. 1 Press /SUBTITLE during playback. The following display appears. 1:ENGLISH 2 Press /SUBTITLE repeatedly to select a setting. ◆ When playing a DVD VIDEO Select the language. Depending on the DVD VIDEO, the choice of language varies. When 4 digits are displayed, they indicate a language code. See "Language Code List" on page 74 to see which language the code represents. ◆ When playing a DVD-VR mode disc Select "ON." 41 42 1-10