Sony GDM-5410 Operation Guide - Page 5

Setup

Get Sony GDM-5410 PDF manuals and user guides View all Sony GDM-5410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Setup This monitor works with platforms running at horizontal frequencies between 30 and 121 kHz. Step 1: Remove the rear cover Before connecting, remove the rear cover of the monitor. Cover Flip open the bottom of the cover and swing out to remove. Step 4: Attach the rear cover Attach the rear cover to the monitor. Pass the AC cord through the cord opening at the bottom of the rear cover. Step 2: Connect your monitor to your computer With the monitor and computer switched off, connect the video signal cable to the video input connector of the monitor and to the video output of the computer. To a computer with an HD15 video output To a computer with an 13W3 video output Notes • Do not touch the pins of the video signal cable connector as this might bend the pins. • When connecting the video signal cable, check the alignment of the connectors. Do not force the connector in the wrong way or the pins might bend. Step 3: Connect the power cord With the monitor and computer switched off, first connect the proper power cord for your local power supply to the monitor, then connect it to a power outlet. Step 5: Turn on the monitor and computer First turn on the monitor, then turn on the computer. The installation of your monitor is complete. If necessary, use the monitor's controls to adjust the picture. If no picture appears on your screen • Check that the monitor is correctly connected to the computer. • If NO INPUT SIGNAL appears on the screen, follow the on- screen messages (page 15). • If you are replacing an old monitor with this model and OUT OF SCAN RANGE appears on the screen, reconnect the old monitor. Then adjust the computer's graphic board so that the horizontal frequency is between 30 - 121 kHz, and the vertical frequency is between 48 - 160 Hz. For more information about the on-screen messages, see "Trouble symptoms and remedies" on page 16. power cord 6 to AC outlet

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
6
Setup
This monitor works with platforms running at horizontal
frequencies between 30 and 121 kHz.
Step 1:Remove the rear cover
Before connecting, remove the rear cover of the monitor.
Step 2:Connect your monitor to
your computer
With the monitor and computer switched off, connect the video
signal cable to the video input connector of the monitor and to the
video output of the computer.
Notes
•
Do not touch the pins of the video signal cable connector as this might
bend the pins.
•
When connecting the video signal cable, check the alignment of the
connectors. Do not force the connector in the wrong way or the pins
might bend.
Step 3:Connect the power cord
With the monitor and computer switched off, first connect the
proper power cord for your local power supply to the monitor,
then connect it to a power outlet.
Step 4:Attach the rear cover
Attach the rear cover to the monitor.
Pass the AC cord through the cord opening at the bottom of the
rear cover.
Step 5:Turn on the monitor and
computer
First turn on the monitor, then turn on the computer.
The installation of your monitor is complete.
If necessary, use the monitor’s controls to adjust the picture.
If no picture appears on your screen
•
Check that the monitor is correctly connected to the computer.
•
If NO INPUT SIGNAL appears on the screen, follow the on-
screen messages (page 15).
•
If you are replacing an old monitor with this model and OUT
OF SCAN RANGE appears on the screen, reconnect the old
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 121 kHz, and the vertical
frequency is between 48 – 160 Hz.
For more information about the on-screen messages, see “Trouble
symptoms and remedies” on page 16.
Cover
Flip open the bottom of
the cover and swing out to
remove.
To a computer
with an HD15
video output
To a computer with an
13W3 video output
power cord
to AC outlet