Sony GDM-90W01T5 Operation Guide - Page 4

Getting Started, Selecting the Input Signal

Get Sony GDM-90W01T5 PDF manuals and user guides View all Sony GDM-90W01T5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Getting Started Before using this monitor, check that the following items are included in your package: • Monitor (1) • This operating instructions (1) This monitor will sync to platforms running at horizontal frequencies between 30 and 96 kHz. Step 1: Connect the monitor to the computer. With the computer switched off, connect the video signal cable to the video output of the computer. Note Do not touch the pins of the video signal cable. to the video output of a computer to the video output of a computer Step 2: Connect the power cord. With the monitor switched off, connect the proper power cord for your local power supply to the monitor and the other end to the power outlet. to a wall outlet Power cord Step 3: Turn on the monitor and computer. Step 4: If necessary, adjust the user controls according to your personal preference. The installation of your monitor is complete. Enjoy your monitor. Selecting the Input Signal This monitor has two signal input connectors and can connect two computers. When the power of both computers is on, select the signal you want to input as follows. 1 Turn on power of the monitor and the computer. 2 Select the input signal. To input the signal from the computer connected to the HD15 connector Set the input select switch to k. To input the signal from the computer connected to the 5 BNC's connector Set the input select switch to K. If only one computer is connected or turned on Set the input select switch to (center position). The input signal is automatically selected. 3 If necessary, adjust the user controls according to your preference on pages 8 to 14. When you set the input select switch to and connect computers to both connectors If you turn on or restart the computer you want to input a signal from, or the computer is in power saving mode, the monitor may automatically select another computer's signal. This is because no signal is input to the monitor at that moment. If this happens, select the signal using the input select switch. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
4
Before using this monitor, check that the following items
are included in your package:
• Monitor (1)
• This operating instructions (1)
This monitor will sync to platforms running at horizontal
frequencies between 30 and 96 kHz.
Step 1: Connect the monitor to the
computer.
With the computer switched off, connect the video signal
cable to the video output of the computer.
Note
Do not touch the pins of the video signal cable.
Getting Started
Step 2: Connect the power cord.
With the monitor switched off, connect the proper power
cord for your local power supply to the monitor and the
other end to the power outlet.
Step 3: Turn on the monitor and
computer.
Step 4: If necessary, adjust the user
controls according to your personal
preference.
The installation of your monitor is complete.
Enjoy your
monitor.
to the video output
of a computer
to the video output
of a computer
Selecting the Input Signal
This monitor has two signal input connectors and can
connect two computers.
When the power of both computers
is on, select the signal you want to input as follows.
1
Turn on power of the monitor and the computer.
2
Select the input signal.
To input the signal from the computer connected to
the HD15 connector
Set the input select switch to
k
.
To input the signal from the computer connected to
the 5 BNC’s connector
Set the input select switch to
K
.
If only one computer is connected or turned on
Set the input select switch to
(center position).
The input signal is automatically selected.
3
If necessary, adjust the user controls according to
your preference on pages 8 to 14.
When you set the input select switch to
and
connect computers to both connectors
If you turn on or restart the computer you want to input a signal
from, or the computer is in power saving mode, the monitor may
automatically select another computer’s signal.
This is because no
signal is input to the monitor at that moment.
If this happens,
select the signal using the input select switch.
to a wall outlet
Power cord