Sony HCD-CP11 Operating Instructions - Page 31

Specifications, Tuner

Get Sony HCD-CP11 - Compact Audio And Video System PDF manuals and user guides View all Sony HCD-CP11 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Additional Information Tuner There is a severe hum or noise ("TUNED" or "STEREO" flashes). • Adjust the antenna. • The signal strength is too weak. Connect an external antenna (see page 9). • Make sure that the antenna is connected properly. • Do not bend or roll up the antenna. • The two wires comprising the FM antenna have been pulled further apart since the system was first purchased. Repair or replace with a new one. • The AM antenna wire is detached from the stand. A stereo FM program cannot be received in stereo. • Press STEREO/MONO on the remote until "STEREO" appears in the display. Resetting the system 1 Disconnect the power cord from the wall outlet. 2 Press ?/1 down and connect the power cord to the wall outlet again. The system is reset to the factory settings. All previous settings such as the preset stations, clock, and timers are cleared and must be set again. Specifications Amplifier section For the U.S. model AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6-ohm loads, both channels driven, from 70 20,000 Hz; rated 18 watts per channel minimum RMS power, with no more than 0.9% total harmonic distortion from 250 milliwatts to rated output. North American model: Continuous RMS power output (reference): 35 + 35 W (6 ohms at 1 kHz, 10% THD) Total harmonic distortion less than 0.07% (6 ohms at 1 kHz, 18 W) European model: DIN power output (rated): 30 + 30 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 35 + 35 W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 85 + 85 W Other models: The following measured at 230 V AC, 60 Hz DIN power output (rated): 30 + 30 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 35 + 35 W (6 ohms at 1 kHz, 10% THD) The following measured at 220 V AC, 60 Hz DIN power output (rated): 24 + 24 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 27 + 27 W (6 ohms at 1 kHz, 10% THD) Inputs MD IN (phono jacks): Sensitivity 500 mV, impedance 47 kilohms VIDEO IN (phono jacks): Sensitivity 250 mV, impedance 47 kilohms Outputs LINE OUT (phono jacks): Sensitivity 250 mV, impedance 1 kilohm OPTICAL DIGITAL OUT (CD): Optical PHONES (stereo phone jack): Accepts headphones with an impedance of 8 ohms or more SPEAKER: Active speaker system, 6 ohms continued 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
31
Additional Information
Tuner
There is a severe hum or noise (“TUNED”
or “STEREO” flashes).
•
Adjust the antenna.
•
The signal strength is too weak. Connect an
external antenna (see page 9).
•
Make sure that the antenna is connected
properly.
•
Do not bend or roll up the antenna.
•
The two wires comprising the FM antenna
have been pulled further apart since the
system was first purchased. Repair or replace
with a new one.
•
The AM antenna wire is detached from the
stand.
A stereo FM program cannot be received
in stereo.
•
Press STEREO/MONO on the remote until
“STEREO” appears in the display.
Resetting the system
1
Disconnect the power cord from the wall outlet.
2
Press
?/1
down and connect the power cord to
the wall outlet again.
The system is reset to the factory settings. All
previous settings such as the preset stations, clock,
and timers are cleared and must be set again.
Specifications
Amplifier section
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6-ohm loads, both channels driven, from 70 -
20,000 Hz; rated 18 watts per channel minimum
RMS power, with no more than 0.9% total
harmonic distortion from 250 milliwatts to rated
output.
North American model:
Continuous RMS power output (reference):
35 + 35 W
(6 ohms at 1 kHz, 10% THD)
Total harmonic distortion less than 0.07% (6 ohms at 1 kHz,
18 W)
European model:
DIN power output (rated):
30 + 30 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
35 + 35 W
(6 ohms at 1 kHz, 10% THD)
Music power output (reference):
85 + 85 W
Other models:
The following measured at 230 V AC, 60 Hz
DIN power output (rated):
30 + 30 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
35 + 35 W
(6 ohms at 1 kHz, 10% THD)
The following measured at 220 V AC, 60 Hz
DIN power output (rated):
24 + 24 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
27 + 27 W
(6 ohms at 1 kHz, 10% THD)
Inputs
MD IN (phono jacks):
Sensitivity 500 mV, impedance 47
kilohms
VIDEO IN (phono jacks):
Sensitivity 250 mV, impedance 47
kilohms
Outputs
LINE OUT (phono jacks): Sensitivity 250 mV, impedance 1
kilohm
OPTICAL DIGITAL OUT (CD):
Optical
PHONES (stereo phone jack):
Accepts headphones with an
impedance of
8 ohms or more
SPEAKER:
Active speaker system, 6 ohms
continued