Sony HCD-EC709iP Service Manual - Page 13

Hcd-ec709ip/ec909ip, Electrical, Check

Get Sony HCD-EC709iP - Cd Deck Receiver Component PDF manuals and user guides View all Sony HCD-EC709iP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

[iPod & iPhone]: Tracking servo setting changes whenever the button is pressed (This function is executable only while CD is playing). "ON": Tracking servo ON. "OFF": Tracking servo OFF. [FUNCTION]: S character mode setting changes whenever the button is pressed. " ": S character mode OFF. "S": S character mode ON. 5. To release from this mode, press three buttons of [u], [iPod & iPhone] and [?/1] simultaneously. SECTION 4 ELECTRICAL CHECK Note: 1. CD Block is basically constructed to operate without adjustment. 2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat- ed. 3. Use an oscilloscope with more than 10 M: impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. 5. Check the focus bias check when optical pick-up block is replaced. FOCUS BIAS CHECK oscilloscope (DC range) BD73 board CL102 (RFOUT) + CL117 (VREF) - Procedure: 1. Connect the oscilloscope to CL102 (RFOUT) and CL117 (VREF) on the CD board. 2. Press the [?/1] button to turn the power on, and press the [FUNCTION] button to select CD function. 3. Set disc (YEDS-18) and press the [u] button to playback. 4. Confirm that oscilloscope waveform is as shown in the figure below (eye pattern). A good eye pattern means that the diamond shape (¡) in the center of the waveform can be clearly distinguished. VOLT/DIV: 200 mV TIME/DIV: 500 ns level: 1.1 ± 0.4 Vp-p Checking Location: - BD73 Board (Conductor Side) - CL117 (VREF) CL102 (RFOUT) IC101 HCD-EC709iP/EC909iP 13 13 HCD-EC709iP/EC909iP

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
HCD-EC709iP/EC909iP
HCD-EC709iP/EC909iP
13
13
[iPod & iPhone]:
Tracking servo setting changes whenever the button is pressed
(This function is executable only while CD is playing).
“ON”: Tracking servo ON.
“OFF”: Tracking servo OFF.
[FUNCTION]:
S character mode setting changes whenever the button is pressed.
“
”: S character mode OFF.
“S”: S character mode ON.
5.
To release from this mode, press three buttons of [
u
], [iPod
& iPhone] and [
?/1
] simultaneously.
SECTION
4
ELECTRICAL
CHECK
Note:
1.
CD Block is basically constructed to operate without adjustment.
2.
Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat-
ed.
3.
Use an oscilloscope with more than 10 M
:
impedance.
4.
Clean the object lens by an applicator with neutral detergent when the
signal level is low than speci
fi
ed value with the following checks.
5.
Check the focus bias check when optical pick-up block is replaced.
FOCUS
BIAS
CHECK
+
–
BD73 board
oscilloscope
(DC range)
CL102 (RFOUT)
CL117 (VREF)
Procedure:
1. Connect the oscilloscope to CL102 (RFOUT) and CL117
(VREF) on the CD board.
2. Press the [
?/1
] button to turn the power on, and press the
[FUNCTION] button to select CD function.
3.
Set disc (YEDS-18) and press the [
u
] button to playback.
4. Con
fi
rm that oscilloscope waveform is as shown in the
fi
gure
below (eye pattern).
A good eye pattern means that the diamond shape (
¡
) in the
center of the waveform can be clearly distinguished.
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.1 ± 0.4 Vp-p
Checking Location:
– BD73 Board (Conductor Side) –
IC101
CL102
(RFOUT)
CL117
(VREF)