Sony HCD-EC709iP Service Manual - Page 17

For Schematic Diagrams., For Printed Wiring Boards.

Get Sony HCD-EC709iP - Cd Deck Receiver Component PDF manuals and user guides View all Sony HCD-EC709iP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. Note: • X: Parts extracted from the component side. • Y: Parts extracted from the conductor side. • W : Indicates side identified with part number. • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen (Conductor Side) from the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Component Side) the parts face are indicated. • Indication of transistor. C Q These are omitted. BE Q BCE These are omitted. • Abbreviation AUS : Australian model CND : Canadian model For Schematic Diagrams. Note: • All capacitors are in —F unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ÿ and 1/4 W or less unless otherwise specified. • f : Internal component. • 2: Nonflammable resistor. • C : Panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. • A : B+ Line. • B : B- Line. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. - BD73 board - no mark: CD PLAY - Other boards - no mark: TUNER (FM/AM) ( ): CD PLAY < > : iPod & iPhone • Voltages are taken with VOM (Input impedance 10 M:). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : TUNER (FM/AM) J : CD PLAY i : iPod & iPhone f : PC IN • Abbreviation AUS : Australian model CND : Canadian model • Circuit Boards Location BD73 board PANEL board HCD-EC709iP/EC909iP MAIN board JACK board IP board POWER board HCD-EC709iP/EC909iP 17 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
HCD-EC709iP/EC909iP
HCD-EC709iP/EC909iP
17
17
For Schematic Diagrams.
Note:
• All capacitors are in
±
F unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in
²
and 1/4 W or less unless otherwise
specified.
•
f
: Internal component.
•
2
: Nonflammable resistor.
•
C
: Panel designation.
THIS
NOTE
IS
COMMON
FOR
PRINTED
WIRING
BOARDS
AND
SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
•
A
: B+ Line.
•
B
: B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
– BD73 board –
no mark
: CD PLAY
– Other boards –
no mark
: TUNER (FM/AM)
(
): CD PLAY
<
> : iPod & iPhone
• Voltages are taken with VOM (Input impedance 10 M
:
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: TUNER (FM/AM)
J
: CD PLAY
i
: iPod & iPhone
f
: PC IN
• Abbreviation
AUS
: Australian model
CND
: Canadian model
For Printed Wiring Boards.
Note:
•
X
: Parts extracted from the component side.
•
Y
: Parts extracted from the conductor side.
•
W
: Indicates side identified with part number.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
• Indication of transistor.
C
B
These are omitted.
E
Q
B
These are omitted.
C
E
Q
• Abbreviation
AUS
: Australian model
CND
: Canadian model
Note:
The components identi-
fied by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Note:
Les composants identifiés
par une marque
0
sont
critiques pour la sécurité.
Ne les remplacer que par
une pièce portant le nu-
méro spécifié.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Circuit Boards Location
MAIN board
JACK board
POWER board
IP board
BD73 board
PANEL board