Sony HCD-XG500 Service Manual - Page 15

Mechanical Adjustments, Deck Clock°set], Enter/next], Disc°3]

Get Sony HCD-XG500 - Bookshelf System PDF manuals and user guides View all Sony HCD-XG500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

SECTION 5 MECHANICAL ADJUSTMENTS Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagne- tizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power sup- ply voltage unless otherwise noted. Torque Measurement Mode Torque Meter FWD CQ-102C FWD back tension CQ-102C REV CQ-102RC REV back tension CQ-102RC FF/REW CQ-201B FWD tension CQ-403A REV tension CQ-403A Meter Reading 3.1~6.96 mN•m (31 to 71 g•cm) (0.43 - 0.98 oz•inch) 0.20~0.58 mN•m (2 to 6 g•cm) (0.03 - 0.08 oz•inch) 3.1~6.96 mN•m (31 to 71 g•cm) (0.43 - 0.98 oz • inch) 0.20~0.58 mN•m (2 to 6 g•cm) (0.03 - 0.08 oz • inch) 6.97~14.02 mN•m (71 to 143 g•cm) (0.99 - 1.99 oz • inch) 9.80 mN•m (100 g or more) (3.53 oz or more) 9.80 mN•m (100 g or more) (3.53 oz or more) HCD-XG60/XG500 SECTION 6 ELECTRICAL ADJUSTMENTS DECK SECTION 0 dB = 0.775 V Precaution 1. Demagnetize the record/playback head with a head demagne- tizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjust. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and RCH. 7. Switches and controls should be set as follows unless otherwise specified. 8. Set to the DOLBY NR OFF. 9. Set to the test mode. (1) Press the ?/1 button to turn the power ON. (2) Select the function "TAPE A or B". (3) Press the button of [ c /CLOCK SET], [ENTER/NEXT], and [DISC 3] simultaneously, to set the tape deck test mode and displays "TEST MODE" on the fluorescent indicator tube. (4) To release from the test mode, press the ?/1 button. • Test Tape Tape P-4-A100 WS-48B P-4-L300 Signal 10 kHz, - 10 dB 3 kHz, 0 dB 315 Hz, 0 dB Used for Azimuth Adjustment Tape Speed Adjustment Playback Level Adjustment 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
15
HCD-XG60/XG500
SECTION
5
MECHANICAL
ADJUSTMENTS
SECTION
6
ELECTRICAL
ADJUSTMENTS
Precaution
1.
Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2.
Demagnetize the record/playback head with a head demagne-
tizer.
3.
Do not use a magnetized screwdriver for the adjustments.
4.
After the adjustments, apply suitable locking compound to the
parts adjusted.
5.
The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.
Torque Measurement
Mode
Torque Meter
Meter Reading
3.1~6.96 mN•m
FWD
CQ-102C
(31 to 71 g•cm)
(0.43 – 0.98 oz•inch)
FWD
0.20~0.58 mN•m
back tension
CQ-102C
(2 to 6 g•cm)
(0.03 – 0.08 oz•inch)
3.1~6.96 mN•m
REV
CQ-102RC
(31 to 71 g•cm)
(0.43 – 0.98 oz • inch)
REV
0.20~0.58 mN•m
back tension
CQ-102RC
(2 to 6 g•cm)
(0.03 – 0.08 oz • inch)
6.97~14.02 mN•m
FF/REW
CQ-201B
(71 to 143 g•cm)
(0.99 – 1.99 oz • inch)
9.80 mN•m
FWD tension
CQ-403A
(100 g or more)
(3.53 oz or more)
9.80 mN•m
REV tension
CQ-403A
(100 g or more)
(3.53 oz or more)
Precaution
1.
Demagnetize the record/playback head with a head demagne-
tizer.
2.
Do not use a magnetized screwdriver for the adjustments.
3.
After the adjustments, apply suitable locking compound to the
parts adjust.
4.
The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5.
The adjustments should be performed in the order given in
this service manual.
(As a general rule, playback circuit ad-
justment should be completed before performing recording
circuit adjustment.)
6.
The adjustments should be performed for both L-CH and R-
CH.
7.
Switches and controls should be set as follows unless other-
wise specified.
8.
Set to
the DOLBY NR OFF.
9.
Set to the test mode.
(1)
Press the
?
/
1
button to turn the power ON.
(2)
Select the function “TAPE A or B”.
(3) Press the button of
[°°°°/CLOCK°SET]
,
[ENTER/NEXT]
,
and
[DISC°3]
simultaneously, to set the tape deck test mode
and displays “TEST MODE”
on the fluorescent indicator
tube.
(4)
To release from the test mode, press the
?
/
1
button.
•
Test Tape
Tape
Signal
Used for
P-4-A100
10 kHz, – 10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0 dB
Tape Speed Adjustment
P-4-L300
315 Hz, 0 dB
Playback Level Adjustment
0 dB = 0.775 V
DECK
SECTION
c