Sony KDL-46EX710 Setup Guide (Operating Instructions) - Page 5

Setting up your TV, Attaching the Table-Top Stand - picture in picture

Get Sony KDL-46EX710 - 46inch Bravia Ex710 Series Led Hdtv PDF manuals and user guides
UPC - 027242807990
View all Sony KDL-46EX710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Setting up your TV Some TV models are packaged with a detached Table-Top Stand so you can mount your TV to a wall right away. If you are not mounting the TV to a wall, you will need to attach the Table-Top Stand. You will need a Phillips screwdriver and the supplied screws to complete the task. Look for the attachment instructions provided with the TV. Be sure to consider the following while setting up your TV: • Disconnect all cables when carrying the TV. • Carry the TV with the adequate number of people; larger size TVs require two or more people. • Correct hand placement while carrying the TV is very important for safety and to avoid damage. Attaching the Table-Top Stand (except KDL-60EX700/60EX701/ 60EX703 models) Refer to the supplied Table-Top Stand instruction leaflet for proper attachment. 1 Gently slide the TV unit onto the Table-Top Stand and align the screw holes. ~ • Do not put stress on the LCD panel or the frame around the screen. • Be careful to not pinch your hands or the AC power cord when you install the TV unit to the Table-Top Stand. Setting up your TV • Ensure your TV has adequate ventilation, see page 13. • For best picture quality, do not expose the screen to direct illumination or sunlight. • Avoid installing the TV in a room with reflective wall and floor materials. • Avoid moving the TV from a cold area to a warm area. Sudden room temperature changes may cause moisture condensation. This may cause the TV to show poor picture and/or poor color. Should this occur, allow moisture to evaporate completely before powering the TV on. 2 Use the supplied screws to attach the TV unit to the Table-Top Stand. ~ • If you use an electric screwdriver, set the tightening torque at approximately 1.5 N·m {15 kgf·cm}. 3 After all the screws are tighten cover the Table-Top Stand with the supplied Stand Rear Cover. ~ • You can attach the TV to the Table-Top Stand with the Stand Rear Cover on with the exception of the 32" and 40" models. The 32" and 40" models must follow the above instructions. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
5
Setting up your TV
Setting up your TV
Some TV models are packaged with a detached
Table-Top Stand so you can mount your TV to
a wall right away. If you are not mounting the
TV to a wall, you will need to attach the
Table-Top Stand. You will need a Phillips
screwdriver and the supplied screws to
complete the task. Look for the attachment
instructions provided with the TV.
Be sure to consider the following while setting
up your TV:
•
Disconnect all cables when carrying the
TV.
•
Carry the TV with the adequate number of
people; larger size TVs require two or more
people.
•
Correct hand placement while carrying the
TV is very important for safety and to avoid
damage.
•
Ensure your TV has adequate ventilation,
see page 13.
•
For best picture quality, do not expose the
screen to direct illumination or sunlight.
•
Avoid installing the TV in a room with
reflective wall and floor materials.
•
Avoid moving the TV from a cold area to a
warm area. Sudden room temperature
changes may cause moisture condensation.
This may cause the TV to show poor picture
and/or poor color. Should this occur, allow
moisture to evaporate completely before
powering the TV on.
Attaching the Table-Top
Stand
(except KDL-60EX700/60EX701/
60EX703 models)
Refer to the supplied Table-Top Stand
instruction leaflet for proper attachment.
1
Gently slide the TV unit onto the
Table-Top Stand and align the screw
holes.
~
•
Do not put stress on the LCD panel or the frame
around the screen.
•
Be careful to not pinch your hands or the AC
power cord when you install the TV unit to the
Table-Top Stand.
2
Use the supplied screws to attach the
TV unit to the Table-Top Stand.
~
•
If you use an electric screwdriver, set the
tightening torque at approximately 1.5 N·m
{15 kgf·cm}.
3
After all the screws are tighten cover
the Table-Top Stand with the supplied
Stand Rear Cover.
~
•
You can attach the TV to the Table-Top Stand
with the Stand Rear Cover on with the exception
of the 32" and 40" models. The 32" and 40"
models must follow the above instructions.