Sony KDL32L4000 Operating Instructions - Page 20

Setting Up the Channel List - Initial Setup, Initial Setup, Auto Program, Channel, Program, Wide Mode - screen

Page 20 highlights

Getting Started Setting Up the Channel List - Initial Setup After you finish connecting your TV, you need to run Initial Setup, which automatically sets up available channels. The Initial Setup screen appears when you turn on your TV for the first time. If you do not want to set up the channels at this time, you can do it later by selecting the Auto Program option in the Channel settings (see page 29). POWER 1 Press to turn on the TV. The Initial Setup screen appears. 2 Press V/v to highlight the desired language. 3 The message "First please connect cable or antenna. Allow 50+ minutes for completion." and "Start auto program now?" appear, make sure you already connected cable or antenna, then select OK to start Auto Program. If you want to start Auto Program later, select Cancel. Initial Setup Please select your language English Español Français Initial Setup First please connect cable or antenna. Allow 50+ minutes for completion. Start auto program now? OK Cancel If you have cable and antenna available, please connect cable first. 4 The scanning of channels will start. If you want to stop and run Auto Program later, press Cancel. 5 When Auto Program is complete, press to continue. 6 If the Initial Setup programming Initial Setup Analog Channels Found: 0 Digital Channels Found: 0 Searching... Please wait. Allow 50+ minutes for completion. Press to cancel. Cancel found cable channels, you will be able to scan antenna channels as well. Connect the antenna using an A-B RF switch (not supplied) and change the switch to antenna then start Auto Initial Setup If you want to use air signals, please connect antenna. Allow 50+ minutes for completion. OK Cancel Program to search antenna channels. If the Initial Setup programming found antenna channels, the Auto Program process will finish. If you want to scan cable channels, you can do it later using the Channel settings. To run Auto Program again at a later time ❑ Use the Auto Program feature as described on page 29. To display the Picture in your Preferred Aspect Ratio ❑ Select the proper Wide Mode as described on pages 22 and 27. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

Getting Started
20
Setting Up the Channel List - Initial Setup
After you finish connecting your TV, you need to run
Initial Setup
, which
automatically sets up available channels. The
Initial Setup
screen appears
when you turn on your TV for the first time. If you do not want to set up the
channels at this time, you can do it later by selecting the
Auto Program
option in the
Channel
settings (see page 29).
1
Press
to turn on the TV.
The
Initial Setup
screen appears.
2
Press
V
/
v
to highlight the desired
language.
3
The message “First please connect
cable or antenna. Allow 50+ minutes
for completion.” and “Start auto
program now?” appear, make sure you
already connected cable or antenna,
then select
OK
to start
Auto Program
.
If you want to start
Auto Program
later, select
Cancel
.
4
The scanning of channels will start. If
you want to stop and run
Auto
Program
later, press
Cancel
.
5
When
Auto Program
is complete,
press
to continue.
6
If the
Initial Setup
programming
found cable channels, you will be able
to scan antenna channels as well.
Connect the antenna using an A-B RF
switch (not supplied) and change the
switch to antenna then start
Auto
Program
to search antenna channels.
If the
Initial Setup
programming found antenna channels, the
Auto
Program
process will finish. If you want to scan cable channels, you
can do it later using the
Channel
settings.
To run Auto Program again at a later time
Use the
Auto Program
feature as described on page 29.
To display the Picture in your Preferred Aspect Ratio
Select the proper
Wide Mode
as described on pages 22 and 27.
If you have cable and antenna available, please connect cable first.
Please select your language
Initial Setup
English
Español
Français
Initial Setup
First please connect cable or antenna.
Allow 50+ minutes for completion.
Start auto program now?
OK
Cancel
POWER
Initial Setup
Analog Channels Found:
0
Digital Channels Found:
0
Cancel
Searching...
Please wait. Allow 50+ minutes for completion.
Press
to cancel.
Initial Setup
If you want to use air signals,
please connect antenna.
Allow 50+ minutes for completion.
OK
Cancel