Sony MHC-GX8000 Operating Instructions (primary manual) - Page 10

Programming the CD, tracks

Page 10 highlights

Playing the CD (continued) To Do this Play repeatedly (Repeat Play) Press REPEAT repeatedly to select "REPEAT"*1 or "REPEAT 1"*2. Cancel Repeat Play Press REPEAT until "REPEAT" or "REPEAT 1" disappears from the display. Exchange other CDs Press DISC SKIP while playing EX-CHANGE. Remove the CD Press OPEN/CLOSE Z. *1 All the tracks repeated up to five times. You cannot use this function during SHUFFLE ALL DISCS. *2 To repeat the current track you are playing. Tip Pressing the CD while the power is off automatically turns the power on and CD is selected as a function. Programming the CD tracks -- Program Play You can make a program of up to 25 tracks from all the CDs in the order you want them to be played. 1 Press CD. 2 Press PLAY MODE repeatedly until "PROGRAM" appears in the display. 3 Press one of the DISC 1~3 to select a CD. To program all the tracks on a CD at once, proceed to step 5 while "AL" appears on the display. 4 Press . or > repeatedly until the track you want appears in the display. Disc tray number Track number Total playing time (including selected track) PROGRAM 5 Press ENTER. The track(s) is (are) programmed. The program step number appears, followed by the total playing time. 6 To program additional tracks, repeat steps 3 to 5. Skip step 3 to select tracks from the same disc. 7 Press hH. To Cancel Program Play Clear a track from the end Add a track to the program when playback is stopped Do this Press PLAY MODE repeatedly until "1 DISC" or "ALL DISCS" appears in the display. Press CLEAR on the remote when playback is stopped. 1 Press one of the DISC 1~3 buttons to select a CD. 2 Press . or > repeatedly to select the track. 3 Press ENTER. Tips • The program you made remains in the system's memory even after it has been played back. Press hH to play the same program again. • If "--.--" appears instead of the total playing time during programming, this means: - you have programmed a track number which exceeds 20. - the total playing time has exceeded 100 minutes. 10GB MHC-RG77 4-238-409-11 (2)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

10
GB
MHC-RG77
4-238-409-
11
(2)
To
Play repeatedly
(Repeat Play)
Cancel Repeat
Play
Exchange other CDs
while playing
Remove the CD
*1
All the tracks repeated up to five times.
You cannot use this function during SHUFFLE
ALL DISCS.
*2
To repeat the current track you are playing.
Tip
Pressing the CD while the power is off automatically
turns the power on and CD is selected as a function.
Programming the CD
tracks
–– Program Play
You can make a program of up to 25 tracks
from all the CDs in the order you want them to
be played.
1
Press CD.
2
Press PLAY MODE repeatedly until
“PROGRAM” appears in the display.
3
Press one of the DISC 1~3 to select a
CD.
To program all the tracks on a CD at once,
proceed to step 5 while
AL
appears on the
display.
Playing the CD (continued)
Do this
Press REPEAT repeatedly to
select
REPEAT
*1
or
REPEAT 1
*2
.
Press REPEAT until
REPEAT
or
REPEAT 1
disappears from the display.
Press DISC SKIP
EX-CHANGE.
Press OPEN/CLOSE
Z
.
4
Press
.
or
>
repeatedly until the
track you want appears in the display.
5
Press ENTER.
The track(s) is (are) programmed. The
program step number appears, followed by
the total playing time.
6
To program additional tracks, repeat
steps 3 to 5.
Skip step 3 to select tracks from the same
disc.
7
Press
hH
.
To
Cancel Program Play
Clear a track from
the end
Add a track to the
program when
playback is stopped
Tips
The program you made remains in the system
s
memory even after it has been played back. Press
hH
to play the same program again.
If
--.--
appears instead of the total playing time
during programming, this means:
you have programmed a track number
which exceeds 20.
the total playing time has exceeded 100 minutes.
Track
number
Total playing time
(including selected
track)
PROGRAM
Disc tray
number
Do this
Press PLAY MODE
repeatedly until
1 DISC
or
ALL DISCS
appears in
the display.
Press CLEAR on the remote
when playback is stopped.
1
Press one of the DISC
1~3 buttons to select a
CD.
2 Press
.
or
>
repeatedly to select the
track.
3
Press ENTER.