Sony MZ-NE410 Operating Instructions - Page 59

If check-out (check-in) was not successful, Cause/Remedy

Get Sony MZ-NE410 - Net MD Walkman MiniDisc Recorder PDF manuals and user guides
UPC - 027242612792
View all Sony MZ-NE410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

• If the installation seems to be stopped It may take 30 minutes or more for the installation to complete, depending on your computer or CD-ROM drive. During the installation, watch out for the occurrence of any of the following problems. Problem Cause/Remedy The installation appears to have Check for the appearance of an error message beneath stopped before it has the installation window. completed. t Press the [Tab] key while holding down the [Alt] key. If an error message has appeared, press the [Enter] key. The installation will resume. If there is no message, the installation is still in progress. Wait a little while longer. The progress bar on the display The installation is progressing normally. Please wait. is not moving. The access lamp has not lit for a few minutes. • If the installation is still unsuccessful after all that you have done. - The installation can be done by copying all files to the hard disk as follows: 1 Create a new folder on the hard disc. 2 Insert the supplied CD-ROM (SonicStage Ver.1.5) into the CD-ROM drive. 3 When the installation window appears, click [Exit] to cancel the installation. 4 Right-click the start menu and start up Explorer. 5 Select [SS15E] on the CD-ROM drive, and then click [Edit] -[Select All]. 6 Click [Edit]-[Copy to Folder] (or [Edit]-[Copy]) to copy all files to the folder that you created in step 1. 7 Remove the CD-ROM from the CD-ROM drive, open the folder that was copied to the hard disk and double-click [setup.exe]. 8 When the installation window appears, follow the displayed instructions to install [SonicStage 1.5]. - The installation may be done by installing the software from [Start]-[Run]. If check-out (check-in) was not successful • Was the battery power sufficient? If the battery becomes exhausted during a check-out (or check-in), the check-out (or check-in) will not be completed. In this case, replace the dry battery with a new one and try again. • Is the surrounding temperature too low? During a check-out (or check-in), make sure the surrounding temperature is +5 ° C (+41° F) or higher. If the temperature is low, the recorder's operation will become slow because of the nature of the battery. 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
59
•
If the installation seems to be stopped
It may take 30 minutes or more for the installation to complete, depending on your
computer or CD-ROM drive.
During the installation, watch out for the occurrence of any of the following problems.
•
If the installation is still unsuccessful after all that you have done.
— The installation can be done by copying all files to the hard disk as follows:
1
Create a new folder on the hard disc.
2
Insert the supplied CD-ROM (SonicStage Ver.1.5) into the CD-ROM drive.
3
When the installation window appears, click [Exit] to cancel the installation.
4
Right-click the start menu and start up Explorer.
5
Select [SS15E] on the CD-ROM drive, and then click [Edit] -[Select All].
6
Click [Edit]-[Copy to Folder] (or [Edit]-[Copy]) to copy all files to the folder that you
created in step 1.
7
Remove the CD-ROM from the CD-ROM drive, open the folder that was copied to the
hard disk and double-click [setup.exe].
8
When the installation window appears, follow the displayed instructions to install
[SonicStage 1.5].
— The installation may be done by installing the software from [Start]-[Run].
If check-out (check-in) was not successful
•
Was the battery power sufficient?
If the battery becomes exhausted during a check-out (or check-in), the check-out (or
check-in) will not be completed. In this case, replace the dry battery with a new one and
try again.
•
Is the surrounding temperature too low?
During a check-out (or check-in), make sure the surrounding temperature is +5
°
C
(+41
°
F) or higher. If the temperature is
low, the recorder’s operation will become slow
because of the nature of the battery.
Problem
Cause/Remedy
The installation appears to have
stopped before it has
completed.
Check for the appearance of an error message beneath
the installation window.
t
Press the [Tab] key while holding down the [Alt]
key. If an error message has appeared, press the [Enter]
key. The installation will resume. If there is no
message, the installation is still in progress. Wait a little
while longer.
The progress bar on the display
is not moving. The access lamp
has not lit for a few minutes.
The installation is progressing normally. Please wait.