Sony PCV-RX450 System Reference Manual - Page 55

Installing a 3.5-inch Internal Hard Disk Drive

Get Sony PCV-RX450 - Vaio Desktop Computer PDF manuals and user guides View all Sony PCV-RX450 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Removing, Installing, and Replacing Components 41 Installing a 3.5-inch Internal Hard Disk Drive Your system comes with an available bay to hold an additional 3.5-inch hard disk drive. The drive you install must not require front panel access. The hard disk drive access light blinks when either internal drive is active. ✍ Some models, such as Configure-to-Order (CTO) systems, may already have a second hard disk drive installed. ! Before opening the system unit, save and close all open files, exit all open applications, turn off the power to all attached peripheral devices, shut down the computer, and unplug the power cord. 1 Configure the jumpers on the new drive as a slave device (see your drive's documentation for configuration instructions). Power connector Jumpers Drive connector 2 Remove the side cover (see "Removing the Side Cover" on page 24).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Removing, Installing, and Replacing Components
41
Installing a 3.5-inch Internal Hard Disk Drive
Your system comes with an available bay to hold an additional 3.5-inch
hard disk drive. The drive you install must not require front panel access.
The hard disk drive access light blinks when either internal drive is
active.
1
Configure the jumpers on the new drive as a slave device (see your
drive’s documentation for configuration instructions).
2
Remove the side cover (see
“Removing the Side Cover”
on page 24).
✍
Some models, such as Configure-to-Order (CTO) systems, may already have a
second hard disk drive installed.
!
Before opening the system unit, save and close all open files, exit all open
applications, turn off the power to all attached peripheral devices, shut
down the computer, and unplug the power cord.
Power connector
Jumpers
Drive connector