Sony SA-WCT100 Service Manual - Page 2
SAFETY, CHECK-OUT, LEAKAGE, Notes on chip component replacement - service manual
View all Sony SA-WCT100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
SA-WCT100/SS-MCT100 1280 × 720p@50 Hz 1920 × 1080i@50 Hz 1920 × 1080p@50 Hz Audio inputs BD, DVD, SAT: Linear PCM 7.1ch/ Dolby Digital/DTS Satellite speaker (SS-MCT100) Speaker system Speaker units Dimensions (approx.) Mass (approx.) Bass reflex, magnetically shielded 40 × 70 mm (1 5/8 × 2 7/8 inches) cone type 800 × 68 × 65 mm (31 1/2 × 2 3/4 × 2 5/8 inches) (w/h/d) 2 kg (4 lb 7 oz) 1920 × 1080p@24 Hz Active subwoofer (SA-WCT100) Speaker system Bass reflex Speaker unit 160 mm (6 1/2 inches) cone type Dimensions (approx.) 160 × 500 × 360 mm (6 3/8 × 19 3/4 × 14 1/4 inches) (w/h/d) Mass (approx.) 10 kg (22 lb 1 oz) Power requirements AC 120 V/60 Hz Power consumption On: 70 Watts Active Standby (Control for HDMI is on): Signal in: 5 Watts (maximum) No signal: 1.5 Watts (minimum) Standby (Control for HDMI is off): 0.3 Watts Design and specifications are subject to change without notice. Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be dam- aged by heat. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 μF 1.5 kΩ AC voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SAFETY-RELATED COMPONET WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2