Sony SLV-340 Operating Instructions primary manual - Page 35

General, setup, information

Get Sony SLV-340 PDF manuals and user guides View all Sony SLV-340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Additional Information General setup information TV • RF UNIT CH3 CH4 01 BONY POWER CHANNEL +/- • cf) TV/VTR Setting the RF unit When connecting the VCR to the TV using only the antenna cable, you must set the RF UNIT switch on the rear of the VCR so that the TV can receive the correct signal from the VCR. If you connect the VCR to the TV using the supplied audio/video cable, you can skip this step. 1 Set the RF UNIT switch on the rear of the VCR to CH3 or CH4, whichever channel is not used in your area. If both are used, set the switch to either channel. 2 Press POWER to turn on the VCR. 3 Press TV/VTR to turn on the VTR indicator in the VCR's display window. 4 Press CHANNEL +/- to display a channel number in the display window. Select an active channel number in your area. 5 Turn on your TV and set it to the channel you selected in step 1 (channel 3 or 4). The selected TV channel broadcast appears on the.TV screen. If the channels change when you press CHANNEL +/-, you have made the correct setting. Whenever you use the VCR, set the TV to the channel selected in step 1. 300-ohm twin lead cable EAC-32 Antenna connector (not supplied) Attaching the external antenna connector When using a 300-ohm twin lead cable for VHF/UHF antenna, use the EAC-32 antenna connector (not supplied) to connect the antenna to the VCR. 1 Loosen the screws on the antenna connector. 2 Wind the twin leads around the screws on the antenna connector. 3 Retighten the screws. 300-ohm twin lead cable 75-ohm coaxial cable EAC-66 UHF/VHF band separator/mixer (not supplied) Attaching an UHFNHF band mixer When using both 75-ohm coaxial cable and 300-ohm twin lead cable for VHF/UHF antenna, use the EAC-66 UHF/VHF band separator/mixer (not supplied) to connect the antenna to the VCR. 1 Loosen the screws on the mixer. 2 Wind the twin leads around the screws on the mixer. 3 Retighten the screws. 4 Connect the 75-ohm coaxial cable to the mixer. Additional Operations 35 -EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
Additional
Information
General
setup
information
•
RF
UNIT
CH3
CH4
01
TV
BONY
POWER
CHANNEL
+/-
•
cf)
TV/VTR
300
-ohm
twin
lead
cable
EAC-32
Antenna
connector
(not
supplied)
300
-ohm
twin
lead
cable
EAC-66
UHF/VHF
band
separator/mixer
(not
supplied)
75
-ohm
coaxial
cable
Setting
the
RF
unit
When
connecting
the
VCR
to
the
TV
using
only
the
antenna
cable,
you
must
set
the
RF
UNIT
switch
on
the
rear
of
the
VCR
so
that
the
TV
can
receive
the
correct
signal
from
the
VCR.
If
you
connect
the
VCR
to
the
TV
using
the
supplied
audio/video
cable,
you
can
skip
this
step.
1
Set
the
RF
UNIT
switch
on
the
rear
of
the
VCR
to
CH3
or
CH4,
whichever
channel
is
not
used
in
your
area.
If
both
are
used,
set
the
switch
to
either
channel.
2
Press
POWER
to
turn
on
the
VCR.
3
Press
TV/VTR
to
turn
on
the
VTR
indicator
in
the
VCR's
display
window.
4
Press
CHANNEL
+/-
to
display
a
channel
number
in
the
display
window.
Select
an
active
channel
number
in
your
area.
5
Turn
on
your
TV
and
set
it
to
the
channel
you
selected
in
step
1
(channel
3
or
4).
The
selected
TV
channel
broadcast
appears
on
the.
TV
screen.
If
the
channels
change
when
you
press
CHANNEL
+/—,
you
have
made
the
correct
setting.
Whenever
you
use
the
VCR,
set
the
TV
to
the
channel
selected
in
step
1.
Attaching
the
external
antenna
connector
When
using
a
300
-ohm
twin
lead
cable
for
VHF/UHF
antenna,
use
the
EAC-32
antenna
connector
(not
supplied)
to
connect
the
antenna
to
the
VCR.
1
Loosen
the
screws
on
the
antenna
connector.
2
Wind
the
twin
leads
around
the
screws
on
the
antenna
connector.
3
Retighten
the
screws.
Attaching
an
UHFNHF
band
mixer
When
using
both
75
-ohm
coaxial
cable
and
300
-ohm
twin
lead
cable
for
VHF/UHF
antenna,
use
the
EAC-66
UHF/VHF
band
separator/mixer
(not
supplied)
to
connect
the
antenna
to
the
VCR.
1
Loosen
the
screws
on
the
mixer.
2
Wind
the
twin
leads
around
the
screws
on
the
mixer.
3
Retighten
the
screws.
4
Connect
the
75
-ohm
coaxial
cable
to
the
mixer.
Additional
Operations
35
-EN