Sony STR-DE595 Operating Instructions - Page 20

Checking the connections - remote

Get Sony STR-DE595 - Fm Stereo/fm-am Receiver PDF manuals and user guides View all Sony STR-DE595 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Multi channel surround setup (continued) Adjusting the speaker level Use the remote while seated in your listening position to adjust the level of each speaker. Note The receiver incorporates a new test tone with a frequency centered at 800 Hz for easier speaker level adjustment. 1 Press ?/1 on the remote to turn on the receiver. 2 Press TEST TONE on the remote. "T. TONE" appears in the display and you will hear the test tone from each speaker in sequence. Front (left) t Center t Front (right) t Surround (right) t Surround (left) t Sub woofer 3 Adjust the speaker level and balance using the LEVEL menu so that the level of the test tone sounds the same from each speaker. For details on the LEVEL menu, see page 27. While adjusting, the test tone is output from the speaker whose adjustment is performed. 4 Press TEST TONE again to turn off the test tone. Tip You can adjust the level of all speakers at the same time. Press MASTER VOL +/- on the remote or turn MASTER VOLUME on the receiver. Notes • (STR-DE595 only) The test tone cannot be output when the receiver is set to MULTI CH IN. • The adjusted value are shown in the display during adjustment. • Although these adjustments can also be made via the front panel using the LEVEL menu (when the test tone is output, the receiver switches to the LEVEL menu automatically), we recommend you follow the procedure described above and adjust the speaker levels from your listening position using the remote. Checking the connections After connecting all of your components to the receiver, do the following to verify that the connections were made correctly. 1 Press ?/1 to turn on the receiver. 2 Turn on the component that you connected (e.g., CD player or tape deck). 3 Press the input selector button (e.g., CD/SACD (STR-DE595 only) / CD (STR-DE495 only) or MD/TAPE) to select the component (program source). 4 Start playing. If you do not obtain normal sound output after performing this procedure, see "Troubleshooting" on page 41 and take the appropriate measures to correct the problem. 20GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
20
GB
Adjusting the speaker level
Use the remote while seated in your listening
position to adjust the level of each speaker.
Note
The receiver incorporates a new test tone with a
frequency centered at 800 Hz for easier speaker level
adjustment.
1
Press
?/1
on the remote to turn on the
receiver.
2
Press TEST TONE on the remote.
“
T. TONE
”
appears in the display and you
will hear the test tone from each speaker in
sequence.
Front (left)
t
Center
t
Front (right)
t
Surround (right)
t
Surround (left)
t
Sub woofer
3
Adjust the speaker level and balance
using the LEVEL menu so that the level
of the test tone sounds the same from
each speaker.
For details on the LEVEL menu, see page
27.
While adjusting, the test tone is output from
the speaker whose adjustment is performed.
4
Press TEST TONE again to turn off the
test tone.
Tip
You can adjust the level of all speakers at the same
time. Press MASTER VOL +/
–
on the remote or turn
MASTER VOLUME on the receiver.
Notes
•
(STR-DE595 only) The test tone cannot be output
when the receiver is set to MULTI CH IN.
•
The adjusted value are shown in the display during
adjustment.
•
Although these adjustments can also be made via
the front panel using the LEVEL menu (when the
test tone is output, the receiver switches to the
LEVEL menu automatically), we recommend you
follow the procedure described above and adjust the
speaker levels from your listening position using the
remote.
Checking the connections
After connecting all of your components to the
receiver, do the following to verify that the
connections were made correctly.
1
Press
?/1
to turn on the receiver.
2
Turn on the component that you
connected (e.g., CD player or tape
deck).
3
Press the input selector button
(e.g., CD/SACD (STR-DE595 only) / CD
(STR-DE495 only) or MD/TAPE) to
select the component (program
source).
4
Start playing.
If you do not obtain normal sound output after
performing this procedure, see
“
Troubleshooting
”
on page 41 and take the
appropriate measures to correct the problem.
Multi channel surround setup
(continued)