Sony VGC-RA940G VAIO User Guide - Page 83
Replacing the drive holder - motherboard
View all Sony VGC-RA940G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 83 highlights
10. Push the drive holder handle down to lock the drive into position. Replacing the driv e holder 11. Reconnect the SATA and power connectors to the original drive. 12. Connect another SATA interface cable between the new drive and an unused SATA port on the motherboard. 13. Connect the second power connector to the new drive following the instructions supplied with the drive. 14. Replace the side panel. See About Closing the Computer. 15. Reconnect the power cord to your computer. The hard disk drive access light blinks when either internal hard disk drive is active. Page 83
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
10.
Push the drive holder handle down to lock the drive into position.
Replacing the drive holder
11.
Reconnect the SATA and power connectors to the original drive.
12.
Connect another SATA interface cable between the new drive and an unused SATA port on the motherboard.
13.
Connect the second power connector to the new drive following the instructions supplied with the drive.
14.
Replace the side panel. See
About Closing the Computer
.
15.
Reconnect the power cord to your computer.
The hard disk drive access light blinks when either internal hard disk drive is active.
Page 83