Sony VPL-CX3 Operating Instructions - Page 34

Sound, Remote Commander, Others, Symptom, Cause and Remedy - troubleshooting

Get Sony VPL-CX3 - XGA LCD Projector PDF manuals and user guides
UPC - 027242578531
View all Sony VPL-CX3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Symptom Cause and Remedy Color balance is incorrect. • Picture has not been adjusted properly. c Adjust the picture (see page 26). • Projector is set to wrong color system. c Set COLOR SYS in the PICTURE CTRL menu to match the color system being input (see page 27). The picture is too dark. • Contrast or brightness has not been adjusted properly. c Adjust the contrast or brightness in the PICTURE CTRL menu properly (see page 26). The picture is not clear. • Picture is out of focus. c Adjust the focus (see page 22). • Condensation has occurred on the lens. c Leave the projector for about two hours with the power on. The picture appears too small on the screen. • SHIFT in the INPUT SETTING menu has not been adjusted properly. c Adjust SHIFT in the INPUT SETTING menu properly (see page 28). The picture flickers. • DOT PHASE in the INPUT SETTING menu has not been adjusted properly. c Adjust DOT PHASE in the INPUT SETTING menu properly (see page 27). Sound Symptom Cause and Remedy No sound. • Cable is disconnected or the connections are wrong. c Check that the proper connections have been made (see page 15). When sound is input • Monaural sound is being input through the AUDIO connector. through AUDIO connector, c Input stereo sound. sound comes through one channel only. Remote Commander Symptom Cause and Remedy The Remote Commander • The Remote Commander batteries are dead. does not work. c Replace with a new battery (see page 12). Others Symptom The LAMP/COVER indicator flashes. The LAMP/COVER indicator lights up. Cause and Remedy • The lamp cover or the air filter cover is detached. c Attach the cover securely (see page 31). • The lamp has reached the end of its life. c Replace the lamp (see page 31). • The lamp becomes a high temperature. c Wait for 90 seconds to cool down the lamp and turn on the power again (see page 23). GB 34 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
GB
34
Troubleshooting
Sound
Remote Commander
Others
Color balance is incorrect.
• Picture has not been adjusted properly.
c
Adjust the picture (see page 26).
• Projector is set to wrong color system.
c
Set COLOR SYS in the PICTURE CTRL menu to match the
color system being input (see page 27).
The picture is too dark.
• Contrast or brightness has not been adjusted properly.
c
Adjust the contrast or brightness in the PICTURE CTRL menu
properly (see page 26).
The picture is not clear.
• Picture is out of focus.
c
Adjust the focus (see page 22).
• Condensation has occurred on the lens.
c
Leave the projector for about two hours with the power on.
The picture appears too
small on the screen.
• SHIFT in the INPUT SETTING menu has not been adjusted
properly.
c
Adjust SHIFT in the INPUT SETTING menu properly (see
page 28).
The picture flickers.
• DOT PHASE in the INPUT SETTING menu has not been adjusted
properly.
c
Adjust DOT PHASE in the INPUT SETTING menu properly
(see page 27).
Symptom
Cause and Remedy
No sound.
• Cable is disconnected or the connections are wrong.
c
Check that the proper connections have been made (see page
15).
When sound is input
through AUDIO connector,
sound comes through one
channel only.
• Monaural sound is being input through the AUDIO connector.
c
Input stereo sound.
Symptom
Cause and Remedy
The Remote Commander
does not work.
• The Remote Commander batteries are dead.
c
Replace with a new battery (see page 12).
Symptom
Cause and Remedy
The LAMP/COVER
indicator flashes.
• The lamp cover or the air filter cover is detached.
c
Attach the cover securely (see page 31).
The LAMP/COVER
indicator lights up.
• The lamp has reached the end of its life.
c
Replace the lamp (see page 31).
• The lamp becomes a high temperature.
c
Wait for 90 seconds to cool down the lamp and turn on the
power again (see page 23).
Symptom
Cause and Remedy