Sony VPL-EX120 Operating Instructions - Page 20

The Connection/Power Menu - projector manual

Get Sony VPL-EX120 PDF manuals and user guides View all Sony VPL-EX120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

The Connection/Power Menu The Connection/Power menu is used for setting for the connections and power. Items Item descriptions Network Setting*3 IP Address Setup Auto (DHCP): The IP address is assigned automatically from the DHCP server such as a router. Manual: To specify the IP Address manually. IP Address/ Subnet Mask/ Default Gateway/Primary DNS/Secondary DNS When "Manual" is selected for "IP Address Setup," select the item with the B or b key and input the value with V or v key. When all items are entered, select "Apply" then press the ENTER key. The entered settings will be registered. Input-A Signal Sel. Auto/Computer/Video GBR/Component: When set to "Auto," selects the type of video signal input automatically when "Input-A" is selected with the INPUT key.*1 Color System Standby Mode*2 Auto/NTSC3.58/PAL/SECAM/NTSC4.43/PAL-M/PAL-N: When set to "Auto," selects the color system automatically when "S Video" or "Video" is selected with the INPUT key.*1 Standard/Low: When set to "Low," lowers power consumption in Standby mode. Power Saving Mode Lamp Cutoff: The lamp turns off automatically and power consumption is reduced if no signal is input for 10 minutes. The lamp lights again when a signal is input or any key is pressed. In Lamp Cutoff, the ON/STANDBY indicator lights in orange (page 26). Standby: The power will be turned off automatically and the projector goes to Standby mode if no signal is input for 10 minutes. Off: The Power Saving Mode is canceled. Direct Power On On/Off: When set to "On," you can turn the power on without going to Standby mode when the AC power cord is connected to a wall outlet. Regardless of the Direct Power On setting, you can disconnect the AC power cord to turn off the power without going to the Standby mode. Notes *1: The image may not be adjusted properly depending on the type of input signal. In such a case, adjust it manually to suit to the connected equipment. *2: When "Standby Mode" is set to "Low," the network and network control function cannot be operated while the projector is in standby mode. *3: VPL-EX145/EX175 only. 20 The Connection/Power Menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
20
The Connection/Power Menu
The Connection/Power Menu
The Connection/Power menu is used for setting for the connections and power.
*1:
The image may not be adjusted properly depending on the type of input signal. In such a case,
adjust it manually to suit to the connected equipment.
*2:
When “Standby Mode” is set to “Low,” the network and network control function cannot be
operated while the projector is in standby mode.
*3:
VPL-EX145/EX175 only.
Items
Item descriptions
Network Setting
*3
IP Address Setup
Auto (DHCP):
The IP address is assigned automatically from the
DHCP server such as a router.
Manual:
To specify the IP Address manually.
IP Address/ Subnet
Mask/ Default
Gateway/Primary
DNS/Secondary
DNS
When “Manual” is selected for “IP Address Setup,” select the item
with the
B
or
b
key and input the value with
V
or
v
key. When all
items are entered, select “Apply” then press the ENTER key. The
entered settings will be registered.
Input-A Signal Sel.
Auto/Computer/Video GBR/Component:
When set to “Auto,”
selects the type of video signal input automatically when “Input-A”
is
selected with the INPUT key.
*1
Color System
Auto/NTSC
3.58
/PAL/SECAM/NTSC
4.43
/PAL-M/PAL-N:
When set
to “Auto,” selects the color system automatically when “S Video” or
“Video” is selected with the INPUT key.
*1
Standby Mode
*2
Standard/Low:
When set to “Low,” lowers power consumption in
Standby mode.
Power Saving Mode
Lamp Cutoff:
The lamp turns off automatically and power
consumption is reduced if no signal is input for 10 minutes. The lamp
lights again when a signal is input or any key is pressed. In Lamp
Cutoff, the ON/STANDBY indicator lights in orange (page 26).
Standby:
The power will be turned off automatically and the projector
goes to Standby mode if no signal is input for 10 minutes.
Off:
The Power Saving Mode is canceled.
Direct Power On
On/Off:
When set to “On,” you can turn the power on without going
to Standby mode when the AC power cord is connected to a wall
outlet. Regardless of the Direct Power On setting, you can disconnect
the AC power cord to turn off the power without going to the Standby
mode.
Notes