Sony VPL-SW536C Operating Instructions - Page 30

Items, Item descriptions, SSID: VPL + MAC address for LAN

Get Sony VPL-SW536C PDF manuals and user guides View all Sony VPL-SW536C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Items Direct Power On Item descriptions On/Off: When set to "On," you can turn the power on without going to Standby mode when the AC power cord is connected to a wall outlet. With the projector turned off, you can also unplug the AC power cord without going to Standby mode, regardless of the Direct Power On setting. Notes *1: This may not be optimum depending on the input signal. In this case set manually according to the connected equipment. *2: When "Standby Mode" is set to "Low," the network and network control function cannot be operated while the projector is in standby mode. *3: This varies depending on the "Lamp Mode" setting. *4: As the lamp is dimmed gradually, you may not notice any change in brightness. You might only notice that the lamp has dimmed when its brightness is restored after there is a change in input signal. *5: This mode does not work for about three minutes after the lamp lights. A change in signal may not be detected depending on the input image. The lamp may become brighter at intervals during lamp dimming. However, this is not a malfunction. If With No Input is set, it takes priority. *6: Select "Off" to avoid entering standby mode when there is no input signal. *7: Does not function when "Type A USB", "Type B USB" or "Network" is selected as the input. In this case, it becomes equivalent to "Standard." *8: Reflecting changes in WLAN settings may take a few moments. *9: To set the IP address manually, select "Manual", press "Apply", then enter the IP address. *10: When you send images or files from a tablet PC/smartphone and display them (page 44), USB wireless LAN module IFU-WLM3 (not supplied) can be used as a wireless access point. *11: The factory default settings for "Manual" are as follows. SSID: VPL + MAC address for LAN Security Method: WEP(64bit) Password: sony1 To change the settings for "Manual", use a web browser. If "Manual" is set, when you use Presentation Function via Network (page 42), select "Manual Connect" to connect to the network. 30 The Connection/Power Menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
30
The Connection/Power Menu
*1:
This may not be optimum depending on the input signal. In this case set manually according
to the connected equipment.
*2:
When “Standby Mode” is set to “Low,” the network and network control function cannot be
operated while the projector is in standby mode.
*3:
This varies depending on the “Lamp Mode” setting.
*4:
As the lamp is dimmed gradually, you may not notice any change in brightness. You might only
notice that the lamp has dimmed when its brightness is restored after there is a change in input
signal.
*5:
This mode does not work for about three minutes after the lamp lights. A change in signal may
not be detected depending on the input image. The lamp may become brighter at intervals
during lamp dimming. However, this is not a malfunction. If With No Input is set, it takes
priority.
*6:
Select “Off” to avoid entering standby mode when there is no input signal.
*7:
Does not function when “Type A USB”, “Type B USB” or “Network” is selected as the input.
In this case, it becomes equivalent to “Standard.”
*8:
Reflecting changes in WLAN settings may take a few moments.
*9:
To set the IP address manually, select “Manual”, press “Apply”, then enter the IP address.
*10:
When you send images or files from a tablet PC/smartphone and display them (page 44), USB
wireless LAN module IFU-WLM3 (not supplied) can be used as a wireless access point.
*11:
The factory default settings for “Manual” are as follows.
SSID: VPL + MAC address for LAN
Security Method: WEP(64bit)
Password: sony1
To change the settings for “Manual”, use a web browser.
If “Manual” is set, when you use Presentation Function via Network (page 42), select “Manual
Connect” to connect to the network.
Direct Power On
On/Off:
When set to “On,” you can turn the power on without going to
Standby mode when the AC power cord is connected to a wall outlet.
With the projector turned off, you can also unplug the AC power cord
without going to Standby mode, regardless of the Direct Power On
setting.
Notes
Items
Item descriptions