TASCAM CD-D1X4 x4 Owners Manual - Page 19

The Session Mode option, Cascading

Page 19 highlights

7 - Other functions 4 Press MODE to view the hardware information (the maximum speed available and the model hardware serial number): H/W INFO x16 1110800000000000 5 Press MODE once more to view the number of discs successfully copied (OK) and the The Session Mode option The SESSION MODE option should always be left as CLOSE. Cascading When two units are cascaded, the master unit can use up to four slave drives of the slave unit. 1 With the two power switches on each unit turned OFF, use the supplied cascade cable to link the two units. 2 Set the switch on the rear of one unit to MASTER, and on the other to SLAVE. Note that if you set both to MASTER or both to SLAVE, neither unit will work properly. 3 Turn on the rear power switches and then turn on the front power switches (always turning on the slave first). number of discs for which copying has been attempted (TOTAL) so far. Note that discs on which track extraction has been performed are not included in these totals. OK TOTAL 1321 1334 There is one exception to this: if you are adding data to audio discs using a computer to make CD-EXTRA discs. Consult the reference manual of your computer CD-R software for details. The slave unit shows Slave Mode on the display. The slave front panel controls and display are disabled, except for the drive eject keys, headphone jacks and volume controls (which can be used at the appropriate points in the different procedures). When the cascade master is cycling through the slave drives, it uses eight drives instead of four (slave drive 1 on the slave unit becomes drive 5, etc.). All other operations are carried out as usual. NOTE If you turn off the SLAVE unit when two units are connected in cascade mode, the MASTER unit cannot be used. TASCAM CD-D1x4 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22

7 – Other functions
TASCAM CD-D1x4
19
4
Press
MODE
to view the hardware informa-
tion (the maximum speed available and the
model hardware serial number):
5
Press
MODE
once more to view the number
of discs successfully copied (
OK
) and the
number of discs for which copying has been
attempted (
TOTAL
) so far. Note that discs
on which track extraction has been per-
formed are not included in these totals.
The Session Mode option
The
SESSION MODE
option should always be
left as
CLOSE
.
There is one exception to this: if you are adding data
to audio discs using a computer to make CD-EXTRA
discs. Consult the reference manual of your computer
CD-R software for details.
Cascading
When two units are cascaded, the master unit can use
up to four slave drives of the slave unit.
1
With the two power switches on each unit
turned OFF, use the supplied cascade cable
to link the two units.
2
Set the switch on the rear of one unit to
MASTER
, and on the other to
SLAVE
. Note
that if you set both to
MASTER
or both to
SLAVE
, neither unit will work properly.
3
Turn on the rear power switches and then
turn on the front power switches (always
turning on the slave first).
The slave unit shows
Slave Mode
on the
display.
The slave front panel controls and display are dis-
abled, except for the drive eject keys, headphone
jacks and volume controls (which can be used at the
appropriate points in the different procedures).
When the cascade master is cycling through the slave
drives, it uses eight drives instead of four (slave drive
1 on the slave unit becomes drive 5, etc.).
All other operations are carried out as usual.
NOTE
If you turn off the
SLAVE
unit when two units are con-
nected in cascade mode, the
MASTER
unit cannot be
used.
H/W INFO
x16
1110800000000000
OK
1321
TOTAL
1334