TASCAM Celesonic US-20x20 Reference Manual V2.10 - Page 17
MUTE buttons
View all TASCAM Celesonic US-20x20 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
6 - Using the Settings Panel w MUTE buttons Click a MUTE button to mute that channel. These buttons light for channels that are muted. (Default: off ) NOTE In addition to turning the MUTE button on and off, channels will be automatically muted and unmuted when SOLO buttons are used e Pan sliders Use to adjust the stereo positions of the signals input to each channel. Use the mouse to click and drag a pan slider left or right to adjust the stereo position. While dragging the mouse, the adjusted position is shown above the channel level fader (t). The value is L20 when set all the way to the left, R20 when set all the way to the right and C when centered. Setting range: L20-L1, C (default value), R1-R20 (41 steps total) The pan slider appears blue when centered (C) and yellow at all other positions. NOTE • When the pan slider is centered (C), signals are reduced by 3 dB and sent to the left and right buses. • Double-click the pan slider to return it to the center (C) position. • When the pan slider is at the left end (L20), the signal is sent only to the left bus of the stereo bus. It is not sent to the right bus. • When the pan slider is at the right end (R20), the signal is sent only to the right bus of the stereo bus. It is not sent to the left bus. r Channel faders Use these to adjust the levels of the signals sent from each channel to the stereo bus. Range: −infinity to 6 dB (default: −infinity) Use the mouse to click and drag a channel fader up or down to adjust its level. The gain value of the channel fader is shown in the fader level display area (y). NOTE Double-click the fader to set it to 0 dB. t Channel level meters These meters show the signal levels of each channel. The channel level meters appear green at levels of -12 dB or less, yellow at levels from −12 dB to −6 dB and red at levels above −6 dB. Each level meter has an overload indicator at its top. NOTE The channel meters show the levels before being adjusted by the faders. Level meters are not affected by fader adjustments or even their channels being muted. y Fader level display areas These show the levels of the channel faders above them as decibel values. u LINK buttons Click a LINK button to unite odd and even channels as a single stereo channel. When linked, this button lights for those channels. (Default: unlit) When a pair is stereo linked, the buttons and knobs of the channels are combined. The channel level meters are also shown is a stereo pair. See "LINK button overview" on page 20 for details. i Channel notes You can input up to six alphanumeric characters. oo Character input Click one of these areas. The cursor will blink when ready for input. When the unit is ready, use a computer keyboard to input characters. When done inputting, press the computer Enter key to confirm. oo When done inputting characters, you must press the computer Enter key to confirm. If you do not press the Enter key, the input characters will continue to be shown but will not be saved when you switch to a different page from the "MIXER" page. o REVERB button Click the REVERB button to apply reverb. (Default: on) When the reverb is on, the REVERB button lights. NOTE The reverb cannot be turned on if the sampling frequency is 176.4/192kHz. p RETURN knob and indicator Use to adjust the return level, which is the signal from the reverb effect returned to the stereo bus. Range: inf to 6 dB (default: inf ) Use the mouse to click and drag the Return knob up or down to adjust the level. While dragging the mouse, the value being adjusted is shown to the bottom right of the RETURN knob. The indicator lights blue at levels of 0 dB or less and yellow at levels from 0 dB to 6 dB. a AUX MASTER 1/REVERB knob and indicator Use this to adjust the send master level of the signal sent to the AUX 1 bus and reverb effect. Range: inf to 6 dB (default: 0 dB) Use the mouse to click and drag the 1/REVERB knob up or down to adjust the send level. While dragging the mouse, the value being adjusted is shown below and to the right of the 1/REVERB knob. The indicator lights blue at levels of 0 dB or less and yellow at levels from 0 dB to 6 dB. TASCAM US-20x20 17