TP-Link Archer C55 Archer C55EU V1 User Guide

TP-Link Archer C55 Manual

Get TP-Link Archer C55 PDF manuals and user guides View all TP-Link Archer C55 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link Archer C55 manual content summary:

  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 1
    User Guide AC1200 Wireless Dual Band Router Archer C55 REV1.0.0 1910012259
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 2
    Contents About This Guide 1 Chapter 1. Get to Know About Your Router 2 1. 1. Product Overview 3 1. 2. Panel Layout 3 1. 2. 1.Top View 3 1. 2. 2.Back Panel 4 Chapter 2. Connect the Hardware 6 2. 1. Position Your Router 7 2. 2. Connect Your Router 7
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 3
    58 4. 16. 1.IPv6 Status 58 4. 16. 2.IPv6 WAN 58 4. 16. 3.IPv6 LAN 62 4. 17. System Tools 63 4. 17. 1.Time Settings 63 4. 17. 2.LED Control 64 4. 17. 3.Feedback 64 4. 17. 4.Diagnostic 65 4. 17. 5.Firmware Upgrade 66 4. 17. 6.Factory Defaults 67 4. 17. 7.Backup & Restore 67 4. 17. 8.Reboot
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 4
    4. 17. 10.Language 69 4. 17. 11.System Log 70 4. 17. 12.Statistics 70 4. 18. Log Out 71 FAQ 72
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 5
    device. More Info The latest software, management app and utility are available from the Download Center at www.tp-link.com/support. The Quick Installation Guide can be found where you find this guide or inside the package of the router. Specifications can be found on the product page at http://www
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 6
    Chapter 1 Get to Know About Your Router This chapter introduces what the router can do and shows its appearance. It contains the following sections: • Product Overview • Panel Layout
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 7
    to your wired devices. Moreover, it is simple and convenient to set up and use the TP-Link router due to its intuitive web interface and the powerful Tether app. 1. 2. Panel Layout . The system is starting up or firmware is being upgraded. Do not disconnect or power off your router. Power is
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 8
    4GHz wireless band is enabled. The 2.4GHz wireless band is disabled. The 5GHz wireless band is enabled. The 5GHz wireless band is disabled. Internet service is available. The router's Internet port is connected, but the internet is not available. The router's Internet port is not connected. At least
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 9
    Chapter 1 Get to Know About Your Router Item Internet Port Reset Button Power On/Off Button Power Port Wi-Fi On/Off Button Antennas Description For connecting to a DSL/Cable modem, or an Ethernet port. Press and hold this button for about 2 seconds to reset the router to its factory default
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 10
    Chapter 2 Connect the Hardware This chapter contains the following sections: • Position Your Router • Connect Your Router
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 11
    Chapter 2 Connect the Hardware 2. 1. Position Your Router • The product should not be located in a place where it will be exposed to moisture or excessive heat. • Place the router in a location where it can be connected to multiple devices as well as to a power source. • Make sure the cables and
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 12
    -Link_XXXX_5G Connect automatically Connect Smart Device < Settings Wi-Fi Wi-Fi CHOOSE A NETWORK... TP-Link_XXXX TP-Link_XXXX_5G Other... • Method 3: Use the WPS button Wireless devices that support WPS, including Android phones, tablets and most USB network cards, can be connected to your router
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 13
    Chapter 2 Connect the Hardware 1 ) Tab the WPS icon on the device's screen. Here we take an Android phone as an example. 2 ) Immediately press the WPS button on your router. Close to WLAN On TP-LINK YSL David Hotdog Ts_5G Sunny Test 9
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 14
    Chapter 3 Log In This chapter introduces how to log in to the web management page of router.
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 15
    Chapter 3 Log In With the web management page, it is easy to configure and manage the router. The web management page can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft the Internet Explorer, Mozilla Firefox or Apple Safari. Follow the steps below to log in to
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 16
    • Operation Mode • Network • Wireless (2.4GHz or 5GHz) • Guest Network • DHCP • Forwarding • Security • Parental Controls • Access Control • Advanced Routing • Bandwidth Control • IP&MAC Binding • Dynamic DNS • IPv6 • System Tools • Log Out
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 17
    Chapter 4 Configure the Router 4. 1. Status 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Status. You can view the current status information of the router. 13
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 18
    Version - The version information of the router's firmware. • Hardware Version - The version information of the width in use. • MAC Address - The physical address of the router. • WDS Status - The status of the WDS connection is displayed. • WAN - This field displays the current settings of the WAN
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 19
    2. Go to Quick Setup. Configure the Router 3. Click Next to start. Then follow the step-by-step instructions to connect your router to the internet. 4. 3. Operation Mode The router supports two operation modes: Wireless Router mode and Access Point mode. 4. 3. 1. Wireless Router Mode The default
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 20
    for the router. 2. Go to Network > WAN. 3. Configure the IP parameters of the LAN and click Save. Dynamic IP If your ISP provides the DHCP service, please select Dynamic IP, and the router will automatically get IP parameters from your ISP. Click Renew to renew the IP parameters from your ISP
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 21
    Configure the Router • Get IP with Unicast - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP address normally, you can choose this option. (It is rarely required.) • Set DNS server manually - If your ISP gives you one or two DNS addresses, select Set DNS
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 22
    the number of minutes you want to have elapsed before your internet access disconnects. • Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The internet connection can be disconnected
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 23
    Chapter 4 Configure the Router • Service Name/Server Name - The service name and server name should not be can input the value between 0 and 120. The value 0 means no detect. • Set DNS server manually - If your ISP does not automatically assign DNS addresses to the router, select this and enter the
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 24
    the number of minutes you want to have elapsed before your internet access disconnects. • Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The internet connection can be disconnected
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 25
    Chapter 4 Configure the Router Note: Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications are visiting the internet continually in the background. PPTP If your ISP provides PPTP connection, please select PPTP. • Username/Password -
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 26
    enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your internet access disconnects. • Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect 22
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 27
    Chapter 4 Configure the Router on Demand mode. The internet connection can be disconnected automatically after a specified inactivity period (Max Idle Time) and not be able to re-establish when you attempt to access the internet again. 4. 4. 2. LAN 1. Visit http://tplinkwifi.net, and log in with
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 28
    Chapter 4 Configure the Router • IGMP Snooping - IGMP snooping is designed to prevent hosts on a local network from receiving traffic for a multicast group they have not explicitly joined. IGMP snooping is especially useful for bandwidth-intensive IP multicast applications such as IPTV. • IGMP
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 29
    Chapter 4 Configure the Router • WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address in this field. Click Restore Factory MAC to restore the MAC address of WAN port to the factory
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 30
    the wireless channel unless you notice interference problems with another nearby access point. • name (SSID). • Enable WDS - You can select this to enable WDS Bridging, with this function and securely connect to a network. This section will guide you to add a new wireless device to your router
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 31
    Chapter 4 Configure the Router 3. Follow one of the following three methods to connect your client device to the router's Wi-Fi network. Method ONE: Press the WPS Button on Your Client Device 1. Keep the WPS Status as Enabled and click Add Device. 2. Select Press the WPS button of the new device
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 32
    Chapter 4 Configure the Router 3. A success message will appear on the WPS page if the client device has been successfully added to the router's network. Method Three: Enter the Router's PIN 1. Keep the WPS Status as Enabled and get the Current PIN of the router. 2. Enter the router's current PIN
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 33
    Chapter 4 Configure the Router • Disable Wireless Security - The wireless security function can be enabled or disabled. If disabled, wireless clients can connect to the router without a password. It's strongly recommended to choose one of the following modes to enable security. • WPA-PSK/WPA2-
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 34
    Chapter 4 Configure the Router • Radius Server Password - Enter the password for the Radius server. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. • WEP - It is based on the IEEE 802.11 standard. •
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 35
    Chapter 4 Configure the Router 4. Set your schedule, click Add, then click Save. 4. 5. 5. Wireless MAC Filtering Wireless MAC Filtering is used to deny or allow specific wireless client devices to access your network by their MAC addresses. I want to: How can I do that? Deny or allow specific
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 36
    Chapter 4 Configure the Router 6. Click Add New and fill in the blank. 1 ) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB00-07-5F in the MAC Address field. 2 ) Enter wireless client A/B in the Description field. 3 ) Select Enabled in the Status drop-down list. 4 ) Click Save and click Back. 7.
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 37
    Client Isolation - This function isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled. 33
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 38
    Chapter 4 Configure the Router • Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended to enable this function. 4. 5. 7. Wireless Statistics 1. Visit http://tplinkwifi.net, and log in with the username and
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 39
    Chapter 4 Configure the Router 3. Select the band and enable the Guset Network function. 4. Create a network name for your guest network. 5. Set the Max Guests number. 6. Select the Security type and create the Password of the guest network. 7. Set the guest network permissions: • Allow Guest
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 40
    Server - Enable or disable the DHCP server. If disabled, you must have another DHCP server within your network or else you must configure the computer manually. • Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 41
    Chapter 4 Configure the Router 4. 7. 2. DHCP Client List 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to DHCP > DHCP Client List to view the information of the clients connected to the router. • Client Name - The name of the DHCP client.
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 42
    the problem that external hosts cannot initiatively communicate with the specified devices in the local network. With the forwarding feature, the router can traverse the isolation of NAT so that clients on the internet can reach devices on the LAN and realize some specific functions. The TP-Link
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 43
    you are not clear about which port and protocol to use. • If the service you want to use is not in the Common Service Port list, you can enter the corresponding parameters manually. You should verify the port number that the service needs. • You can add multiple virtual server rules if you want to
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 44
    . • The triggering ports can not be overlapped. • If the application you need is not listed in the Common Applications list, please enter the parameters manually. You should verify the incoming ports the application uses first and enter them in Incoming Ports field. You can input at most 5 groups of
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 45
    log in normally but cannot join a team with other players. To solve this problem, set your PC as a DMZ host with all ports opened. 1. Assign a this router. • Only the application supporting UPnP protocol can use this feature. • UPnP feature needs the support of operating system (e.g. Windows Vista
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 46
    Chapter 4 Configure the Router LAN WAN Xbox Router If necessary, you can follow the steps to change the status of UPnP. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Forwarding > UPnP. 3. Click Disable or Enable according to your
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 47
    by default. • VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, (IP) networks, through the use of cryptographic security services. If you want to allow IPSec tunnels to pass be plugged into the gateway to support address and port translation for certain application
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 48
    > Advanced Security, and you can protect the router from being attacked by ICMP-Flood, UDP Flood and TCP-SYN Flood. • DoS Protection - Denial of Service protection. Select Enable or Disable to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 49
    , if you want to allow PCs with specific MAC addresses to access the router's web management page locally from inside the network, please follow the instructions below: 45
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 50
    can change the remote management web port to a custom port by entering a number between 1 and 65534 but do not use the number of any common service port. • Remote Management IP Address - This is the address you will use when accessing your router via a remote device. This function is disabled when
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 51
    's PC with the MAC address 00-11-22-33-44-AA can access www.tp-link.com on Saturday only while the parent PC with the MAC address 00-11-22 schedule with Day is Sat and Time is all day-24 hours. Click Add 6. Enter www.tp-link.com in the Add URL field. Click Add. 7. Click Save. Then you will see the
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 52
    , If you want to restrict the internet activities of host with MAC address 00-11-22-33-44-AA on the LAN to access www.tp-link.com only, please follow the steps below: 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 53
    Chapter 4 Configure the Router 3 ) Click Save. 4. Go to Access Control > Schedule and configure the schedule settings: 1 ) Click Add New. 2 ) Create a unique description (e.g. schedule_1) for the schedule in the Schedule Description field and set the day(s) and time period. 3 ) Click Save. 5.
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 54
    12. Advanced Routing Static Routing is a form of routing that is configured manually by a network administrator or a user by adding entries into a routing table. The manually-configured routing information guides the router in forwarding data packets to the specific destination. 4. 12. 1. Static
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 55
    Chapter 4 1. Click Add New. Configure the Router 2. Enter the following information. • Destination IP Address - The Destination Network is the address of the network or host that you want to assign to a static route. • Subnet Mask - The Subnet Mask determines which portion of an IP address is the
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 56
    Chapter 4 Configure the Router • Destination Network - The Destination Network is the address of the network or host to which the static route is assigned. • Subnet Mask - The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion. •
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 57
    Chapter 4 Configure the Router • Description - This is the information about the rules such as address range. • Egress Bandwidth - This field displays the max and min upload bandwidth through the WAN port. The default is 0. • Ingress Bandwidth - This field displays the max and min download
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 58
    Chapter 4 Configure the Router 4. 14. 1. Binding Settings 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to IP & MAC Binding > Binding Settings. 3. Select Enable for ARP Binding. 4. Click Save. ¾¾ To add IP & MAC Binding entries: 1. Click
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 59
    matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as www.comexe.cn, www.dyndns.org, or www.noip.com. The Dynamic DNS client service provider will give you a password or key. 1. Visit http://tplinkwifi.net, and log in with the
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 60
    Chapter 4 Configure the Router To set up for DDNS, follow these instructions: 1. Enter the Domain Name you received from dynamic DNS service provider here. 2. Enter the Username for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click Login. 5. Click Save. • Connection Status -
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 61
    you select is www.comexe.cn, the following page will appear. To set up for DDNS, follow these instructions: 1. Enter the Domain Name received from your dynamic DNS service provider. 2. Enter the Username for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click Login. 5. Click
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 62
    including Connection Type, IPv6 Address information, IPv6 Default Gateway, Primary IPv6 DNS and Secondary IPv6 DNS. • LAN - This section shows the current IPv6 information of the router's LAN port, including IPv6 Address Assign Type, IPv6 Address and Link-local Address. 4. 16. 2. IPv6 WAN 1. Visit
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 63
    and password. • Tunnel 6to4 - Connections which use 6to4 address assignment. Dynamic IPv6 • IPv6 Address - The IPv6 address assigned by your ISP dynamically. • Prefix Length - The length of IPv6 address prefix. • IPv6 Gateway - Enter the default gateway provided by your ISP. • Addressing Type
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 64
    are sure it is necessary for your ISP connection. If your ISP gives you one or two DNS IPv6 addresses, select Set IPv6 DNS Server manually and enter the IPv6 DNS Server and Secondary IPv6 DNS Server into the correct fields. Otherwise, the DNS servers will be assigned from ISP dynamically. • Enable
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 65
    connection. • Enable MLD Proxy - Enable the Multicast Listener Discovery (MLD) Proxy function if you need. • Use IPv6 address specified by ISP - Input a static IPv6 address from the ISP. • Set IPv6 DNS Server manually - Enter the IP address of the IPv6 DNS server and secondary IPv6 DNS server. 61
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 66
    net, and log in with the username and password you set for the router. 2. Go to IPv6 > IPv6 LAN. 3. Select the Address Autoconfiguration Type which determines the way how the router assigns IPv6 address for PCs on the LAN: • Address Autoconfiguration Type - RADAD (Router Advertisement Daemon) and
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 67
    device will delegate it to the LAN. • Static - Configure the Site Prefix and Site Prefix Length manually. Please contact your ISP to get more information before you configure them. Note: If your IPv6 wan connection type is "Tunnel 6to4", the Site Prefix Configuration Type should be "Static" to make
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 68
    or suggestions to us, so that we can resolve your issues and keep improving product features to give you a better network experience. For technical problems, it is recommended to attach the configuration file or system log of the device to help us investigate your case. 1. Visit http://tplinkwifi
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 69
    Chapter 4 Configure the Router 3. Enter your information, and describe your questions or suggestions. 4. Click Send. 4. 17. 4. Diagnostic Diagnostic is used to test the connectivity between the router and the host or other network devices. 1. Visit http://tplinkwifi.net, and log in with the
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 70
    Ping - This diagnostic tool troubleshoots connectivity, reachability, and name firmware at TP-Link official website. You can download the latest firmware file from the Support page of our website www.tp-link.com and upgrade the firmware to the latest version. 1. Download the latest firmware
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 71
    ://tplinkwifi.net, and log in with the username and password you set for the router. 3. Go to System Tools > Firmware Upgrade. 4. Click Choose File to locate the downloaded firmware file, and click Upgrade. 4. 17. 6. Factory Defaults 1. Visit http://tplinkwifi.net, and log in with the username and
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 72
    Chapter 4 Configure the Router ¾¾ To backup configuration settings: Click Backup to save a copy of the current settings in your local computer. A ".bin" file of the current settings will be stored in your computer. ¾¾ To restore configuration settings: 1. Click Choose File to locate the backup
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 73
    Chapter 4 Configure the Router • Change the Web Management Port. • Upgrade the firmware of the router (system will reboot automatically). • Restore the router to its factory defaults (system will reboot automatically). • Update the configuration with the file (system
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 74
    Chapter 4 Configure the Router 4. 17. 11. System Log 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to System Tools > System Log, and you can view the logs of the router. • Log Type - By selecting the log type, only logs of this type will
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 75
    Chapter 4 Configure the Router The total number of packets received and transmitted in the Packets last Packets Statistic interval seconds. Bytes The total number of bytes received and transmitted in the last Packets Statistic interval seconds. The number of the ICMP packets transmitted to WAN
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 76
    FAQ Q1. What should I do if I forget my wireless password? The default wireless password is printed on the label of the router. If the password has been altered, please connect your computer to the router using an Ethernet cable and follow the steps below: 1. Visit http://tplinkwifi.net, and log in
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 77
    3 ) Click LAN settings and deselect the following three options, and click OK. 73
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 78
    and try again. If the login still fails, please contact the technical support. Note: You'll need to reconfigure the router to surf the internet try again: • Your computer might not recognize any DNS server addresses, please manually configure DNS server. 1 ) Go to DHCP. 2 ) Enter 8.8.8.8 as Primary
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 79
    settings and reconfigure the router. • Upgrade the firmware of the router. • Check the TCP/IP settings LAN IP address of the router. Note: Most TP-Link routers use 192.168.0.1/192.168.1.1 as their cause you can't access the internet. To resolve this problem, we need to change the LAN IP address of
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 80
    the router. • Please upgrade the firmware of the router. If you've tried every method above but cannot access the internet, please contact the technical support. Q5. What should I do is disabled or blocked somehow. 2 ) Clicking Troubleshoot and windows might be able to fix the problem by itself. 76
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 81
    TP-Link Utility, for example). 3 ) Select and right click My Computer on Desktop, and select Manage to open Computer Management window. 4 ) Expand Services and Applications > Services connect, please follow the steps below: • Authenticating problem/password mismatch: 1 ) Sometimes you will be asked
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 82
    • Windows unable to connect to XXXX / Can not join this network / Taking longer than usual to connect to this network: • Check the wireless signal strength of your network, if it is weak (1~3 bars), please move the router closer and try again. • Change the wireless Channel of the router to 1,6,or 11
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 83
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 84
    installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 85
    -2472MHz(20dBm) 5180MHz-5240MHz(23dBm) EU declaration of conformity TP-Link hereby declares that the device is in compliance with the /65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce RF Exposure Information This device meets the EU requirements (2014/53/
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 86
    稱 鉛 Pb 鎘 汞 Cd Hg CrVI PBB PBDE PCB ○ ○ ○ ○ ○ ○ 外殼 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 備考 1. " 超出 0.1 wt 0.01 wt 2 3 Safety Information • Keep the device away from water, fire, humidity or hot environments. • Do not attempt to disassemble, repair,
  • TP-Link Archer C55 | Archer C55EU V1 User Guide - Page 87
    For EU/EFTA, this product can be used in the following countries: AT BE BG CH CY CZ DE DK EE ES FI FR GB GR HR HU IE IS IT LI LT LU MT MT NL NO PL PT RO SE SI SK Explanations of the symbols on the product label Symbol Explanation DC voltage Indoor use only
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
REV1.0.0
1910012259
User Guide
AC1200 Wireless Dual Band Router
Archer C55