TP-Link TL-SL2452 TL-SL2452 V1 User Guide 1910010972 - Page 13

Reset, 100Mbps Ports, 100/1000Mbps Ports, SFP Ports, Speed and Duplex, Switching, Port Config,

Get TP-Link TL-SL2452 PDF manuals and user guides View all TP-Link TL-SL2452 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

The front panel of TL-SL2218 is shown as Figure 2-2. Figure 2-2 Front Panel of TL-SL2218 The front panel of TL-SL2428 is shown as Figure 2-3. Figure 2-3 Front Panel of TL-SL2428 The front panel of TL-SL2452 is show as Figure 2-4. Figure 2-4 Front Panel of TL-SL2452 The following parts are located on the front panel of the switch:  Reset: Press this button for five seconds or above to reset the software setting back to factory default setting.  10/100Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each has a corresponding 10/100M (10/100Mbps) LED.  10/100/1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding 1000M (1000Mbps) LED.  SFP Ports: Designed to install the SFP module. TL-SL2218/TL-SL2428 features some SFP transceiver slots that are shared with the associated RJ45 ports. The associated two ports are referred as a "Combo" port, which means they cannot be used simultaneously, otherwise only SFP port works. Meanwhile, the associated two ports share the same LED. For TL-SL2218, Port 17 shares the same LED with Port 17F and Port 18 shares the same LED with Port 18F; for TL-SL2428, Port 27 shares the same LED with Port 27F and Port 28 shares the same LED with Port 28F. Note: When using the SFP port with a 100Mbps module or a gigabit module, you need to configure its corresponding Speed and Duplex mode on Switching→Port→Port Config page or through Telnet. For 100M module, please select 100MFD while select 1000MFD for gigabit module. By 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
The front panel of TL-SL2218 is shown as Figure 2-2.
Figure 2-2 Front Panel of TL-SL2218
The front panel of TL-SL2428 is shown as Figure 2-3.
Figure 2-3 Front Panel of TL-SL2428
The front panel of TL-SL2452 is show as Figure 2-4.
Figure 2-4 Front Panel of TL-SL2452
The following parts are located on the front panel of the switch:
Reset:
Press this button for five seconds or above to reset the software setting back to factory
default setting.
10/100Mbps Ports:
Designed to connect to the device with a bandwidth of 10Mbps or
100Mbps. Each has a corresponding 10/100M (10/100Mbps) LED.
10/100/1000Mbps Ports:
Designed to connect to the device with a bandwidth of 10Mbps,
100Mbps or 1000Mbps. Each has a corresponding 1000M (1000Mbps) LED.
SFP Ports:
Designed to install the SFP module. TL-SL2218/TL-SL2428 features some SFP
transceiver slots that are shared with the associated RJ45 ports. The associated two ports are
referred as a "Combo" port, which means they cannot be used simultaneously, otherwise only
SFP port works. Meanwhile, the associated two ports share the same LED. For TL-SL2218,
Port 17 shares the same LED with Port 17F and Port 18 shares the same LED with Port 18F;
for TL-SL2428, Port 27 shares the same LED with Port 27F and Port 28 shares the same LED
with Port 28F.
Note:
When using the SFP port with a 100Mbps module or a gigabit module, you need to configure its
corresponding
Speed and Duplex
mode on
Switching
→
Port
→
Port Config
page or through
Telnet. For 100M module, please select
100MFD
while select
1000MFD
for gigabit module. By
6