TRENDnet TW-200 Manual - Page 18

LAN Installation

Get TRENDnet TW-200 PDF manuals and user guides View all TRENDnet TW-200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Error! Reference source not found. User Guide Error! Reference source not found. is allocated a new IP Address during configuration. LAN Installation Installing your new Error! Reference source not found. in your existing Ethernet LAN is quick and easy. Simply follow the instructions below: 1. Choose an Installation Site Select a place on the network to install the Error! Reference source not found.. Remember that you need phone jacks and power outlets near your chosen location. 2. Connect Network Cable The Error! Reference source not found. supports two types of network cables: Thin Ethernet (10Base2, BNC connector) and Twisted Pair Ethernet (10BaseT, RJ-45 connector). During power up, the unit automatically detects the type of network cable and adjusts to that environment. 10Base2 Cabling: If your network uses 10Base2 cable, insert a BNC "T" connector into the Error! Reference source not found.'s BNC port. Connect the cable to one end of the "T" connector and connect the outgoing cable to the other end. If the Error! Reference source not found. is at the end of the network, then cap off the other end of "T" connector with a 50-ohm terminator. Also, keep in mind that the maximum effective length between the ends of a 10Base2 network is 185 meters. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Error! Reference source not found.
User Guide
10
Error! Reference source not found.
is allocated a new IP
Address during configuration.
LAN Installation
Installing your new
Error! Reference source not found.
in
your existing Ethernet LAN is quick and easy. Simply follow
the instructions below:
1.
Choose an Installation Site
Select a place on the network to install the
Error! Refer-
ence source not found.
. Remember that you need phone
jacks and power outlets near your chosen location.
2. Connect Network Cable
The
Error! Reference source not found.
supports two
types of network cables: Thin Ethernet (10Base2, BNC
connector) and Twisted Pair Ethernet (10BaseT, RJ-45
connector). During power up, the unit automatically de-
tects the type of network cable and adjusts to that
environment.
10Base2 Cabling:
If your network uses 10Base2 cable, insert a BNC “T”
connector into the
Error! Reference source not found.
’s
BNC port. Connect the cable to one end of the “T”
connector and connect the outgoing cable to the other end.
If the
Error! Reference source not found.
is at the end of
the network, then cap off the other end of “T” connector
with a 50-ohm terminator. Also, keep in mind that the
maximum effective length between the ends of a 10Base2
network is 185 meters.