TRENDnet TW-200 Manual - Page 19

Connect Modem & Phone Line, Connect Power Adapter, Check the LEDs

Get TRENDnet TW-200 PDF manuals and user guides View all TRENDnet TW-200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Installation 10BaseT Cabling: If your network uses 10BaseT cable, insert one end into the Error! Reference source not found.'s RJ-45 jack and the other end into the 10BaseT hub. Keep in mind that the maximum effective length from the hub to the device is 100 meters. Warning: Do not attempt to connect more than one type of cable at the same time or change the network cable while the Error! Reference source not found. is powered On. 3. Connect Modem & Phone Line Connect the modem, using a standard serial cable, to the Error! Reference source not found.'s serial port. Next, connect a telephone line from an RJ-11 style phone jack to the modem. 4. Connect Power Adapter Connect the modem's power adapter to the modem and the Error! Reference source not found.'s power adapter to the Error! Reference source not found.. Power both devices On. Only use the power adapter provided with your unit. Using a different one may cause hardware damage. 5. Check the LEDs When the Error! Reference source not found. is powered On, both LEDs should light, then the Error LED should go off. If the Error LED stays on, there is a hard- 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Installation
11
10BaseT Cabling:
If your network uses 10BaseT cable, insert one end into
the
Error! Reference source not found.
’s RJ-45 jack and
the other end into the 10BaseT hub. Keep in mind that the
maximum effective length from the hub to the device is
100 meters.
Warning:
Do not attempt to connect more than
one type of cable at the same time or
change the network cable while the
Error! Reference source not found. is
powered On.
3.
Connect Modem & Phone Line
Connect the modem, using a standard serial cable, to the
Error! Reference source not found.
’s serial port. Next,
connect a telephone line from an RJ-11 style phone jack to
the modem.
4. Connect Power Adapter
Connect the modem’s power adapter to the modem and the
Error! Reference source not found.
’s power adapter to
the
Error! Reference source not found.
. Power both de-
vices On.
Only use the power adapter provided
with your unit. Using a different one
may cause hardware damage.
5. Check the LEDs
When the
Error! Reference source not found.
is pow-
ered On, both LEDs should light, then the Error LED
should go off. If the Error LED stays on, there is a hard-