TRENDnet TW100-BRF104 Manual - Page 21

Configuring TCP/IP Properties

Get TRENDnet TW100-BRF104 PDF manuals and user guides View all TRENDnet TW100-BRF104 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

TW100-BRF104 Broadband Router+Firewall If you need the adapter: a. Click the Add button. b. Select Adapter, and then click Add. c. Select the manufacturer and model of your network adapter, and then click OK. If you need TCP/IP: a. Click the Add button. b. Select Protocol, and then click Add. c. Select Microsoft. It is not necessary to remove any other network components shown in the Network window in order to install the adapter, TCP/IP, or Client for Microsoft Networks. d. Select TCP/IP, and then click OK. If you need Client for Microsoft Networks: a. Click the Add button. b. Select Client, and then click Add. c. Select Microsoft. d. Select Client for Microsoft Networks, and then click OK. 3. Restart your computer for the changes to take effect. 3.3.2 Configuring TCP/IP Properties After the TCP/IP protocol components are installed, each computer must be assigned specific information about itself and resources that are available on its network. The simplest way to configure this information is to allow the computer to obtain the information from the internal DHCP server of the TW100-BRF104 Broadband Router+Firewall. If you are using DHCP with the recommended default addresses, you can configure your computers by following these steps: 1. Install TCP/IP on each computer, leaving the computer configured to obtain configuration settings automatically (by DHCP). 2. Connect your Ethernet-interfaced computers to the Broadband Router+Firewall. 3. Restart the TW100-BRF104 Broadband Router+Firewall and allow it to boot. Preparing Your Network 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
TW100-BRF104
Broadband Router+Firewall
Preparing Your Network
3-3
If you need the adapter:
a.
Click the
Add
button.
b.
Select
Adapter
, and then click
Add
.
c.
Select the manufacturer and model of your network adapter, and then click
OK
.
If you need TCP/IP:
a.
Click the
Add
button.
b.
Select
Protocol
, and then click
Add
.
c.
Select
Microsoft
.
It is not necessary to remove any other network components shown in the
Network window in order to install the adapter, TCP/IP, or Client for Microsoft
Networks.
d.
Select
TCP/IP
, and then click
OK
.
If you need Client for Microsoft Networks:
a.
Click the
Add
button.
b.
Select
Client
, and then click
Add
.
c.
Select
Microsoft
.
d.
Select
Client for Microsoft Networks
, and then click
OK
.
3.
Restart your computer for the changes to take effect.
3.3.2 Configuring TCP/IP Properties
After the TCP/IP protocol components are installed, each computer must be assigned specific information
about itself and resources that are available on its network. The simplest way to configure this information
is to allow the computer to obtain the information from the internal DHCP server of the TW100-BRF104
Broadband Router+Firewall.
If you are using DHCP with the recommended default addresses, you can configure your computers by
following these steps:
1.
Install TCP/IP on each computer, leaving the computer configured to obtain configuration settings
automatically (by DHCP).
2.
Connect your Ethernet-interfaced computers to the Broadband Router+Firewall.
3.
Restart the TW100-BRF104 Broadband Router+Firewall and allow it to boot.