Thermador T24ID800LP Installation Manual - Page 10

Required accessories and tools - freezer

Get Thermador T24ID800LP PDF manuals and user guides View all Thermador T24ID800LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Required accessories and tools Supplied accessories  Installation instructions  Operating instructions  Installation kit Optional accessories Sealing Kit for Side-by-Side Installation BSEALKIT10 For permanent connection of two individual appliances, e.g. Freezer next to Refrigerator. Freedom Heater Kit for Side-by-Side Installation XHEATKIT10 If the gap between the appliances is less than 6" (160 mm). Panel unification part (Metal strip) FPCONNTS10 For connection of two door panels. Can be used for standard height door panels without further preliminary work. Other required accessories Ice maker installation kit 1/4" OD copper line For connecting appliances which require water, e.g. for an ice maker. Maximum outer diameter of the water pipe (without fittings): 13/32" (10 mm). Other  Stepladder  Dolly, hand truck  Hammer drill for drilling holes in wall or floor  Bits according suitable for material and in different sizes  Wooden beam (cross section min. 3" x 4") as an alternative tip protection, length according to the width of the installation enclosure  Wooden screws in different sizes  Thin plywood sheet, particle board or cardboard to protect the floor from damage  Suitable material for covering and protecting furniture (e.g. protective sheets)  Adhesive tape Note: Before using, check whether the removed adhesive tape leaves adhesive residue on the work surfaces! Otherwise do not use on high-quality work surfaces. Tools 10 Cordless screwdriver Torx bit T20 + magnetic holder Torx screwdriver T20 5/16" (8 mm) hex nut driver Wood drills in different sizes Open end wrench 1/2" (SW 13 mm) Multigrip pliers Adjustable wrench Cutter with adjustable blade Metal tape measure, folding rule Square Level, length 2' (60 cm) and 4' (1,2 m)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
10
Required accessories and tools
Supplied accessories
Installation instructions
Operating instructions
Installation kit
Optional accessories
Sealing Kit for Side-by-Side Installation BSEALKIT10
For permanent connection of two individual appliances,
e.g. Freezer next to Refrigerator.
Freedom
Heater Kit for Side-by-Side Installation
XHEATKIT10
If the gap between the appliances is less
than 6" (160 mm).
Panel unification part (Metal strip) FPCONNTS10
For connection of two door panels. Can be used
for standard height door panels without further
preliminary work.
Other required accessories
Ice maker installation kit
1
/
4
" OD copper line
For connecting appliances which require water,
e.g. for an ice maker.
Maximum outer diameter of the water pipe
(without fittings):
13
/
32
" (10 mm).
Other
Stepladder
Dolly, hand truck
Hammer drill for drilling holes in wall or floor
Bits according suitable for material and in different
sizes
Wooden beam (cross section min. 3" x 4") as an
alternative tip protection, length according to the
width of the installation enclosure
Wooden screws in different sizes
Thin plywood sheet, particle board or cardboard to
protect the floor from damage
Suitable material for covering and protecting
furniture (e.g. protective sheets)
Adhesive tape
Note:
Before using, check whether the removed adhesive
tape leaves adhesive residue on the work surfaces!
Otherwise do not use on high-quality work surfaces.
Tools
Cordless screwdriver
Torx bit T20 + magnetic
holder
Torx screwdriver T20
5
/
16
" (8 mm) hex nut driver
Wood drills in different sizes
Open end wrench
1
/
2
"
(SW 13 mm)
Multigrip pliers
Adjustable wrench
Cutter with adjustable blade
Metal tape measure,
folding rule
Square
Level, length 2' (60 cm) and
4' (1,2 m)