Thermador T24ID800LP Installation Manual - Page 15

Pushing the appliance into the installation enclosure

Get Thermador T24ID800LP PDF manuals and user guides View all Thermador T24ID800LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

5. Pushing the appliance into the installation enclosure , CAUTION: Caution when pushing the appliance into the installation enclosure. Do not damage the water line or power cord. Note: When the floor or the appliance is not leveled in comparison to the installation enclosure adjust height adjustable wheels before you move the appliance into the installation enclosure. 1. Remove the base panel. 2. Raise the height-adjustable wheels at the back by approx. 3/8" (10 mm). 3. Put the electric plug into the socket. 4. Push the water line into the guard tube (a) at the rear of the appliance. , WARNING: Be careful, otherwise people who are helping may be injured or the appliance may be damaged. The appliance may tip over while the water line is pushing into the guard tube. 5. To prevent the power cord from becoming caught, tie a piece of string to the middle of the power cord and feed forwards over the top of the appliance. When pushing in the appliance, pull the cable upwards. Take care not to pinch the power cord. or Using adhesive tape, tape the power cord to the floor centrally behind the appliance approx. 15" (380 mm) away from the rear panel of the installation enclosure. 6. Carefully push the appliance into the installation enclosure. 7. Remove edge protection (if attached). 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
15
5.
Pushing the appliance into the installation enclosure
,
CAUTION:
Caution when pushing the appliance into the
installation enclosure. Do not damage the water
line or power cord.
Note:
When the floor or the appliance is not leveled in
comparison to the installation enclosure adjust height
adjustable wheels before you move the appliance into
the installation enclosure.
1.
Remove the base panel.
2.
Raise the height-adjustable wheels at the back
by approx.
3
/
8
" (10 mm).
3.
Put the electric plug into the socket.
4.
Push the water line into the guard tube (a) at the rear
of the appliance.
,
WARNING:
Be careful, otherwise people who are helping may
be injured or the appliance may be damaged.
The appliance may tip over while the water line is
pushing into the guard tube.
5.
To prevent the power cord from becoming caught,
tie a piece of string to the middle of the power cord
and feed forwards over the top of the appliance.
When pushing in the appliance, pull the cable
upwards. Take care not to pinch the power cord.
or
Using adhesive tape, tape the power cord to the
floor centrally behind the appliance approx.
15" (380 mm) away from the rear panel of
the installation enclosure.
6.
Carefully push the appliance into the installation
enclosure.
7.
Remove edge protection (if attached).