Toshiba PA3943U-1CAM Camileo P100 User Manual - Page 10

Getting Started, Loading the Battery, Charge your battery - memory card

Get Toshiba PA3943U-1CAM Camileo P100 PDF manuals and user guides View all Toshiba PA3943U-1CAM Camileo P100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Section 2 Getting Started Loading the Battery Before using the camcorder, users must load the Lithium-ion rechargeable battery come within the package. 1. Insert the battery according to the correct polarity marks (+ or -). 2. Close the battery cover firmly. REMOVE Note Please take out the battery from the camcorder and remove the insulator on the battery connection before use. Charge your battery You must use the supplied AC charger or the USB cable. The camcorder must be turned OFF. The blinking light confirms the camcorder is currently charging, and the light becomes constant after the charging is completed. In AC charging Mode, the light will turn itself off automatically after 3~5 minutes. The full charge time is about 3 to 4 hours. (Actual charging time may vary. It depends on the battery conditions.) Inserting and Removing an SD Card (Optional) The camcorder comes with an internal memory which allows you to store photos and videos. You can expand the memory capacity by using an optional SD memory card. 1. Insert the memory card into the slot. Please refer to the figure on the right side. 2. To remove an installed SD card, press the card inwards to release it. 3. When the card pops out, gently remove it from its slot. 4. Recommended memory capacity: 1GB or above. Note • When a memory card is fitted, videos/photos are saved on the card rather than on the built-in memory. • Protecting Data on an SD Card: SD Card is read-only when it is locked. No photos or videos can be recorded when the SD card is locked. Make sure the lock is on the writeable position before recording any media. 10 Writeable position Write-Protected Position EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
10
EN
Section 2
Getting Started
Loading the Battery
Before using the camcorder, users must load the Lithium-ion
rechargeable battery come within the package.
Insert the battery according to the correct polarity marks (+ or -).
1.
Close the battery cover firmly.
2.
Note
Please take out the battery from the camcorder and remove the insulator on the battery
connection before use.
Charge your battery
You must use the supplied AC charger or the USB
cable. The camcorder must be turned OFF. The
blinking light confirms the camcorder is currently
charging, and the light becomes constant after
the charging is completed. In AC charging Mode,
the light will turn itself off automatically after 3~5
minutes. The full charge time is about 3 to 4 hours.
(Actual charging time may vary. It depends on the
battery conditions.)
Inserting and Removing an SD Card (Optional)
The camcorder comes with an internal memory which allows you to
store photos and videos. You can expand the memory capacity by
using an optional SD memory card.
Insert the memory card into the slot. Please refer to the figure
1.
on the right side.
To remove an installed SD card, press the card inwards to
2.
release it.
When the card pops out, gently remove it from its slot.
3.
Recommended memory capacity: 1GB or above.
4.
Note
When a memory card is fitted, videos/photos are saved
•
on the card rather than on the built-in memory.
Protecting Data on an SD Card: SD Card is read-only
•
when it is locked. No photos or videos can be recorded
when the SD card is locked. Make sure the lock is on
the writeable position before recording any media.
Writeable
position
Write-Protected
Position
REMOVE