Toshiba SD-V392 User Manual - Page 13

Remote control basics, Inserting batteries

Get Toshiba SD-V392 - DVD/VCR Combo PDF manuals and user guides
UPC - 022265411254
View all Toshiba SD-V392 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Introduction Inserting batteries 1 Slide the battery compartment cover in the direction of the arrow. 2 Install two "R03/AAA" batteries (supplied), paying attention to the polarity diagram in the battery compartment. 3 Replace the compartment cover. Battery precautions The precautions below should be followed when using batteries in this device: 1. Use only the size and type of batteries specified. 2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Re- versed batteries may cause damage to the device. To avoid a potential short circuit, insert the "-" end first. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer's directions.) Remote control basics • Press POWER ( ) to turn the DVD VCR on or off. • Select your desired operating mode (DVD or VCR) using VCR DVD. (DVD or VCR indicator on the front panel will show you which mode is selected.) • Press CH + or CH - to move through the channels one channel at a time. • The CH +/- ( / ) and SET +/- ( / ) are also used to navigate on-screen menu system. • You can directly access specific channels using Number buttons. • Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the DVD screen (DVD mode). Operation • Aim the remote control at the remote sensor and press control buttons to operate. • Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of Approx. 7 meters. Approx. 7 meters 2C53301C (E)p02-13 13 21/4/04, 11:09 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
13
Introduction
Operation
• Aim the remote control at the remote sensor and press control buttons to
operate.
• Operate the remote control within 30
°
angle on either side of the remote
sensor, up to a distance of Approx. 7 meters.
Replace the compartment
cover.
Install two “R03/AAA” batteries
(supplied),
paying attention to the
polarity diagram in the battery
compartment.
Slide the battery compartment
cover in the direction of the
arrow.
Approx. 7 meters
Battery precautions
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Re-
versed batteries may cause damage to the device.
To avoid a potential short circuit, insert the “–” end first.
3.
Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer’s directions.)
•
Press
POWER (
)
to turn the DVD VCR on or off.
•
Select your desired operating mode (DVD or VCR) using
VCR DVD
.
(DVD or VCR indicator on the front panel will show you which mode is selected.)
•
Press
CH +
or
CH
– to move through the channels one channel at a time.
•
The
CH
+/
–
(
/
)
and
SET +/– (
/
)
are also used to navigate on-screen menu system.
•
You can directly access specific channels using
Number buttons
.
•
Each press of
VCR DVD
on the remote control, switches the screen between the VCR screen (VCR mode) and the
DVD screen (DVD mode).
1
2
3
Remote control basics
Inserting batteries
2C53301C (E)p02-13
21/4/04, 11:09
13